Specifications; Safety Instructions - Makita 7104L Betriebsanleitung

ENGLISH
1. Wing bolt
2. Stopper pole
3. Stopper
4. Lock-off button
5. Switch trigger
6. Adjusting screw
7. Chain bar
8. Chain cover
9. Hex bolt
10. Arrow
11. Sprocket
12. Lever (A)
13. Vise lever

SPECIFICATIONS

Model
Capacities
Max. hole length (Longitudinal) ..................... 130 mm
Max. hole depth ............................................. 155 mm
Width of applicable workpiece ........ 80 mm – 308 mm
-1
Chain speed (min ) ................................................. 300 m
Dimensions (L × W × H) ..... 512 mm × 298 mm × 513 mm
Net weight................................................................. 17 kg
Safety class ............................................................ Class I
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for cutting mortise in wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.

SAFETY INSTRUCTIONS

WARNING:
When using electric tools, basic safety precautions,
including the following, should always be followed to
reduce the risk of fire, electric shock and personal
injury. Read all these instructions before operating
this product and save these instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
Explanation of general view
14. Rear vise
15. Setting handle
16. Front vise
17. Indicator plate
18. Indication plate
19. Cutting line (A)
20. Cutting line (B)
21. Hook
22. Hex bolts
23. Gauge plate
24. Travel distance (D)
25. Lever (B)
26. Lever (C)
2. Consider work area environment.
7104L
3. Guard against electric shock.
4. Keep children away.
5. Store idle tools.
6. Do not force the tool.
7. Use the right tool.
8. Dress properly.
9. Use safety glasses and hearing protection.
10. Connect dust extraction equipment.
11. Do not abuse the cord.
27. Adjusting hex bolt for No. 1 set
position
28. Adjusting hex bolt for No. 2 set
position
29. Original position
30. No.1 set position
31. No.2 set position
32. Ruler
33. Front vise
34. Limit mark
35. Brush holder cap
36. Screwdriver
Do not expose power tools to rain. Do not use power
tools in damp or wet locations. Keep work area well lit.
Do not use power tools where there is risk to cause
fire or explosion.
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
Do not let visitors touch the tool or extension cord. All
visitors should be kept away from work area.
When not in use, tools should be stored in a dry, high
or locked up place, out of reach of children.
It will do the job better and safer at the rate for which it
was intended.
Do not force small tools or attachments to do the job of
a heavy duty tool. Do not use tools for purposes not
intended; for example, do not use circular saws to cut
tree limbs or logs.
Do not wear loose clothing or jewellery, they can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protecting hair covering to contain long hair.
Also use face or dust mask if the cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
Never carry the tool by the cord or yank it to discon-
nect it from the socket. Keep the cord away from heat,
oil and sharp edges.
5