Inhaltsverzeichnis; General Warnings: Safety - Installation - Use - Nice TTPRO BD Installations- Und Bedienungsanleitung

CONTENTS
GENERAL WARNINGS: SAFETY - INSTALLATION - USE
1 - PRODUCT DESCRIPTION AND INTENDED USE
2 - ELECTRICAL CONNECTIONS
3 - PRODUCT OPERATION
3.1 - Function and description of buttons
3.1.1 - Buttons for movements
3.2 - Function and description of the LEDs
3.3 - ON/OFF button
3.3.1 - Switching On of TTPRO BD
3.3.2 - Motor search
3.3.2.A - TTPRO BD connected via TTBUS
3.3.2.B - TTPRO BD connected via RADIO BD
3.3.3 - Forced motor scan
3.3.4 - Switching Off of TTPRO BD
3.4 - Transmitter programming
3.4.1 - Memorisation of the transmitter
3.4.2 - Deleting a single transmitter
3.4.3 - Deleting all transmitters
3.4.4 - Memorising a single transmitter button (Mode 2)
3.4.5 - Deleting a transmitter memorised in Mode 2
3.5 - Basic programming
3.5.1 - Programming the direction of movement
3.5.2 - Programming of positions
3.5.2.A - Manual programming of positions "0", "1" and "I"
3.5.2.B - Automatic programming of the positions "0" and "1"
3.5.3 - Deleting pre-programmed positions
3.6 - Settings/Adjustments
3.6.1 - Setting the type of "dry-contact"
3.6.2 - Setting the time of duration the maneuver
3.6.3 - Setting the speed
3.6.4 - Setting the level "soft-start" and "soft-stop"
3.6.5 - Setting the level of sensitivity to obstacle / DRC
3.7 - Climatic sensors
3.7.1 - Setting the intervention level for "wind" protection
3.7.2 - Enabling/disabling of climatic sensors
3.7.3 - Setting the intervention level for "sun" protection
3.7.4 - Setting the direction of rotation of the motor in case of rain
3.8 - Insights
3.8.1 - Radio test function
3.8.2 - Deleting the parameters from the motor
3.8.3 - Copying parameters and transmitters
3.8.3.1 - Deleting of the parameters stored in TTPRO BD
3.8.4 - Checking the software version
3.8.5 - Updating the TTPRO BD firmware
3.8.6 - Changing the motor address
4 - BATTERY REPLACEMENT
5 - DISPOSAL OF THE PRODUCT
CE DECLARATION OF CONFORMITY
1 - English
GENERAL WARNINGS:
SAFETY - INSTALLATION - USE
1
(instructions translated from Italian)
2
2
2
WARNING For personal safety it is important to observe these instructions.
2
Observe these instructions - improper installation can result in
3
serious injury.
4
WARNING Important safety instructions: keep these instructions.
4
4
WARNING All installation procedures, connections, programming and main-
4
tenance of the product must be performed exclusively by a quali-
4
fied technician!
4
• Do not open the device protection housing as it contains non-serviceable electrical
5
5 circuits.
5
• Never apply modifications to any part of the device. Operations other than as specified
5
can only cause malfunctions. The manufacturer declines all liability for damage caused
5
by makeshift modifications to the product.
5
5
• Never place the device near sources of heat and never expose it to naked flames. This
5
may damage it and cause malfunctions.
5
• This product is not intended to be used by persons (including children) whose physi-
5
cal, sensory or mental capabilities are reduced, or who lack the necessary experience
6
or skill.
6
6
• Make sure that children do not play with the product.
7
7
7
7
8
• Also check the instructions contained in the instruction manual of the motor to which
8
the product is associated.
8
• Handle the product carefully, while avoiding crushing, bumping and dropping it so as
8
to prevent damages to the product.
8
8
• The packing materials of the product must be disposed of in compliance with local
9
regulations.
9
9
9
9
9
10
10
10
10
10
11
11
OTHER WARNINGS