Troubleshootings - De Dietrich 56278 Handbuch

Wall-mounting receiver
ref. 56278
1 channel 433 MHz receiver,
1 contact 16A AC1
1 channel 433 MHz receiver,1 contact 16A AC1,
free of potential
FR GB DE
IT ES
Product presentation
Push button for configuration and priority
setting.
Indicator of Power on and coding light.
LED on = product is powered on.
This LED flickers during coding operations.
Operation indicator light.
The LED is on when receiver's output contact
is closed = ON.
!
The transmitter and receiver assembly is factory
coded and is therefore immediately operational.
Configuration
In order to associate the transmitter with the receiver:
• Press the receiver's push button for more than
3 seconds.
• The indicator OK light will start flickering,
release the push button.
The system is in configuration mode.
• Press the RESET button during 3 seconds of the
transmitter.
• The indicator OK button will stop flickering,
at the end of 5 secondes.
The transmitter/receiver link is now established.
Reset
For clearing all transmission/reception links:
• Press the receiver's push button
than 10 seconds.
• The indicator OK light flickers slowly, then
more quickly.
• Press again the receiver's push button
than 3 seconds.
• The indicator OK light stops flickering, all links
have been cleared.
The receiver returns to the auto mode.
Priority setting
Manual control is provided for this product.
• Press shortly receiver's
sec).
Each press reverses output state.
!
Radio control retains priority.

Troubleshootings

• The heating does not start:
- receiver's power supply is cut off
off). Check fuse and circuit breaker.
• Receiver is outside of transmitter's
range:
- move transmitter closer to receiver.
• Receiver does not recognize transmitter's
code:
- re-install receiver.
• The system does not start or does not stop:
- the receiver or transmitter is disturbed
by radio transmission (radio ham, TV monitor,
cellular phone re-transmitter, etc.): attempt to
remove the source of disturbance.
In case of persistent problem,call on your elec-
trician.
Technical specifications
Supply voltage:
Minimum load:
Output: 1 changeover contact free of potential
Switching capacity:
Radio frequency:
Degree of protection:
for more
Isolation class:
Mechanical protection:
Operating temperature:
Storage temperature:
more
Electrical connection
Dimensions:
Hygrometry:
Receiver class :
Made in France
Usable in all Europe and Switzerland
push button (<3
(OK light is
230 V +10 % at -15 %
12 V 100 mA
Inductive: 3 A (cos ϕ = 0,6) AC1: 16 A 250 V
433.92 MHz
IP43
II
IK04
-10°C to +60°C
-20°C to +70°C
Flexible capacity: 0,5 to 1,5 mm 2
Rigid capacity 0,5 to 2,5 mm 2
130 x 60 x 27 mm
90% max. at 20°C
2
7
The radio receiver is designed to operate with
thermostats and programmable room thermostats
and used to control a boiler or an electric heater.
Installation
!
Before working on the installation, isolate all
electrical supplies. All electrical wiring must
be carried out by a qualified person.
For easier installation, the kit is suppplied with a
flexible 4-wire 1,5 mm cable of 1.20m length (not
2
connected).
We recommend using this cable for connecting the
HF receiver according to the following colour
codes:
brown = phase
blue = neutral
gray }
= connection to the boiler
black
L
L
N
N
L N
L N
5 4 3 2 1
5 4 3 2 1
L
L
N
N
L N
L N
5 4 3 2 1
5 4 3 2 1