Operation - Monacor TXA-110USB Bedienungsanleitung

G
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the plug.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the units and no liability
for any resulting personal damage or material
damage will be accepted if the units are used for
other purposes than originally intended, if they
are not correctly connected or operated, or if they
are not repaired in an expert way.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in
accordance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol , or coloured green or green and
yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.
3 Applications, Accessories
The audio amplifier system TXA-110USB is a port -
able speaker system with amplifier (active speaker
system). It is equipped with an MP3 player with USB
interface and a UHF PLL receiver (16 channels in
the range 863 – 865 MHz). From the MONACOR
product range, the wireless microphone TXA-
100HT and the pocket transmitter TXA-100HSE
with tie clip microphone and headband microphone
are ideally suited for this amplifier system.
Power is supplied from a mains socket via the
power supply unit provided or via the integrated re -
chargeable lead gel battery which allows mains-
independent operation. An integrated charger will
re charge the battery. Thus, the unit is ideally suited
for mobile PA applications at events, lectures, etc.
For PA application of larger zones, set up several ac -
tive speaker systems TXA-110USB (or also model
TXA-110 without MP3 player) to receive and repro-
duce the signal of a single wireless microphone.
However, it is also possible to connect another
active speaker system to the audio output MIX OUT.
The system is supplied with a practical shoulder
bag and a shoulder strap.
4 Setting Up / Transporting
the Active Speaker System
Place the active speaker system as desired or
preferably mount it onto a stand at a height of
1 – 1.5 m above the ground. For stands with a 9 mm
3
( ⁄ ") thread, a threaded jack is provided on the
8
lower side of the active speaker system. For speaker
stands with a standard tube diameter of 36 mm, the
MONACOR stand adapter EBH-48 is available.
For transport, e. g. in case of guided tours, use
the shoulder strap or the shoulder bag provided.
Attach the strap to the eyebolts (1). For operation
inside the shoulder bag, put the active speaker sys-
tem into the bag in such a way that the sound from
the speaker is radiated through the mesh side. To
access the operating elements and connections,
open the lateral flap of the bag (hook and loop fas-
tener).

5 Operation

5.1 Power supply / Recharging the battery
1) To operate the active speaker system via a
mains socket and / or to recharge the internal
battery, connect the power supply unit provided
to the jack DC IN (14) and to a mains socket
(230 V~ / 50 Hz) via the mains cable provided.
When the power supply unit is connected to the
mains socket, the green power LED lights up on
the power supply unit.
2) As soon as the power supply unit supplies
power to the active speaker system, the battery
is recharged: The green charge LED CG (13)
starts flashing. For charging, it is not necessary
to switch on the unit with the switch and volume
control MAIN VOL (11), however, the unit can be
used as usual during the charging process.
3) When the battery has been fully charged, the
charge LED CG lights continuously. At maxi-
mum volume, a mains-independent operating
time of approx. 3 hours is possible. A lower vol-
ume will increase the operating time.
4) Recharge the battery when the red LED PWR / BL
(12) starts flashing while the unit is switched on.
GB
9