IMG STAGELINE TXS-852 Bedienungsanleitung Seite 12

2) Press the button SET repeatedly until the dis-
GB
play shows the current setting for the scan func-
tion:
scan function activated
scan function deactivated
3) Press the button
or the button
.
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.3 Identification number
To set the transmitter to the transmission fre -
quency of the receiver via the REMOSET function
( chapter 5.2), both must have the same identi-
fication number.
1) Keep the button SET (6) pressed until the letter
"G" starts flashing on the display; the group set-
ting mode is activated.
2) Press the button SET repeatedly until the dis-
play shows
number ( ...
3) Select the desired number with the button
or the button
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5) Then set the identification number on the trans-
mitter instruction manual of the transmitter.
5.1.4 Lock function
When the lock function has been activated, the
REMOSET function will not be available (
ter 5.2) and it will not be possible to switch off the
receiver. From the setting modes, you will only be
able to activate the mode for the lock function in
order to deactivate the lock.
Activating the lock
1) Keep the button SET (6) pressed until the letter
"G" starts flashing on the display; the group set-
ting mode is activated.
2) Press the button SET repeatedly until the dis-
play shows
flashing.
3) To activate the lock, press the button
display shows
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
The indication LOCK (e) on the display
shows that the lock has been activated. When
12
(5) to select the setting
(7) to select the setting
. The receiver will return to
and the current identification
).
(7).
. The receiver will return to
(lock off) and LOCK (e) starts
.
. The receiver will return to
you press a button or when you set the on/off
switch (8) to OFF,
Deactivating the lock
1) Make sure that the on/off switch (8) is set to ON.
2) Keep the button SET (6) pressed until the indi-
cation LOCK (e) starts flashing on the display.
3) To deactivate the lock, press the button
The display shows
4) Press the button SET to confirm. The display
briefly shows
normal mode.
5.2 Automatic frequency matching
(REMOSET function)
Via a 2.4 GHz radio signal of the receiver, the trans-
mitter is matched to the transmission frequency of
the receiver. The range of REMOSET transmission
may reach up to 10 m. Transmission is not possible
when the receiver is locked (deactivating the lock
chapter 5.1.4).
After setting the desired transmission frequency
on the receiver (
the transmitter, press the button REMOSET (3).
When the REMOSET function has been activated,
(5)
the luminous ring of the button starts flashing rap-
idly. The display briefly shows the identification
number of the receiver (
matching the frequency, the transmitter is set to the
channel group and the channel of the receiver. The
luminous ring of the button lights permanently
again.
If the luminous ring keeps flashing after the REMO -
SET function has been activated, the re ceiver does
not receive a radio signal from the transmitter on
the transmission frequency adjusted, e. g. when
chap-
REMOSET transmission has failed (troubleshoot-
ing box below) or when the transmitter is muted
at the time of REMOSET transmission.
If the transmitter has not been set to the channel group
and the channel of the receiver, check the following
adjustments on the transmitter:
→ Has the lock function been activated on the trans -
mitter?
→ Has the automatic frequency matching been disabled
on the transmitter?
→ Does the identification number set on the transmitter
differ from the one set on the receiver?
(7). The
Correct the corresponding setting on the transmitter and
press the button REMOSET once again.
appears in addition.
.
. The unit will return to the
chapter 5.1.1) and switching on
chapter 5.1.3). After
(5).