Klarstein 10028129 Bedienungsanleitung Seite 19

For the water tank and ice-full detecting plate
Also the water tank and the ice-full detecting plate is very important to keep your ice cube hygienic.
Put mixture of neutral cleaner & water into a clean water jet, then spray to all the inner surface of
tank & the ice detecting plate. Wipe these surfaces as far as possible with a clean cloth. And then,
spray the surfaces with clean water, wiping with a dry clean cloth. Then drain out the cleaned water
in the water tank by pulling out the Water drain pipe of the water tank indicating "H" in above illus-
tration. When all of the cleaned water has been drained out, to reinstall back the water drain pipe
of the water tank. IMPORTANT: After cleaning the interior parts and install back to its respective
position, and return machine to work, discard first batch of ice.
Ice Making Assembly System Cleaning
Minerals that are removed from water during the freezing cycle will eventually form a hard scaly
deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup.
How often you need to clean the system depends upon how hard your water is. With hard water of 4
to 5 grains/liter, you may need to clean the system as often as every 6 months.
1. Turn off the ice maker. Keep the ice maker connect to the water supply and drainpipe. But shut off
the water faucet of main water supply.
2. Open the door and scoop out all of the ice cubes. Either discard them
or save them in an ice chest or cooler.
3. Making the cleaning solution. Please mix the Nu-Calgon Nickle Safe
Ice Machine Cleaner with water to make the cleaning solution. Wear
rubber gloves and safety goggles when handling Ice Machine Cleaner
or Sanitizer. Use a plastic or stainless container with more than 4 liters
capacity, mix 300 ml Nu-Calgon Nickle Safe Ice-machine Cleaner with
2.8 liters warm water about 50-60°C. Then divide them for 2 shares
equally in 2 cups. It is better to keep the temperature of each cup of
the cleaning solution.
4. Check to be sure that the water drain pipe of the water tank has been installed properly in the
slot of the tank wall. Then Pour one cup of Nickel-Safe Ice Maker Cleaning Solution into the water
tank. Wait about for 5 minutes.
5. Turn on the power to the ice maker, then press "TIMER CLEAN"button on control panel for more
than 5 seconds, to enter the self-Cleaning program. Same as above explanation, the water pump
runs for 8 minutes and stops for 3 minutes, one cycle, again one cycle. The total duration time
is 30 minutes for one self-cleaning program. During this process, the "CLEAN"light will always be
on during this period, and the digit window will indicate the left time,
6. After 30 minutes of one self-cleaning program completing, pull out the drain pipe of the water
tank, drain the cleaning solution down to the lower ice storage bin. Shake the unit slightly to
drain out all of the cleaning solution completely. Then install back the drain pipe to the slot of the
water tank.
7. Repeat steps 4-6 to clean the ice making assembly system again. Then open the water faucet of
the main water supply, Let the water flow in the unit. Again press the"TIMER CLEAN"button on
control panel for more than 5 seconds, to enter the self-Cleaning program. Through this process,
It will rinse the water dividing pipe, evaporator, water pump, silicone pipe, and water tank, etc.
8. After one self-cleaning program complete, then pull out the drain pipe of the water tank, drain the
cleaning solution down to the lower ice storage bin, also shake the unit slightly to drain out all of
the water completely. Then install back the drain pipe to the water tank slot tightly.
9. Repeat the step 8-9 again for 2 times. Following the above program to clean the ice storage bin.
Then this special cleaning program finish, you can return to the regular ice making mode. And
suggest to discard the first batch of ice cube.
19