Klarstein 10028129 Bedienungsanleitung Seite 17

Automatic self-cleaning program
• After connecting all of the water pipe, plug on the main power supply plug, then press "TIMER
CLEAN"button on control panel for more than 5 seconds, to enter the self-Cleaning program. And
the "CLEAN"light will always be on during this period, the digit window will indicate the left time.
The total duration time is 30 minutes for one self-cleaning program. Also when the water pump
stops, the water will supply to the water tank automatically.
• Cancel the self-cleaning program: It takes about 30 minutes to complete one self-cleaning pro-
gram. When the program is over, the system will be in off-state automatically. And also you can
press the "ON/OFF" button on control panel to cancel the self-cleaning program by force.
Off-Timer and ON-Timer Setting
• ON-Timer: During the unit is in off-state, press the "TIMER/CLEAN" button to set the ON-Timer.
The "TIMER" light will start to be on, the number in digital window will flash to display the setting
delay time. During the number flashing, press „+" or "-"button to change the delay time of the ti-
mer, the default setting is zero, 1 hour adding or decreasing per each pressing of "+" or "-" button.
Five seconds after setting, your desired setting will be remembered.
• OFF-Timer: When the unit is working, press the "TIMER/CLEAN" button to set the OFF-Timer. The
"TIMER" light will start to be on, the number in digital window will flash to display the setting delay
time. During the number flashing, press „+" or "-"button to change the delay time of the timer, the
default setting is zero, 1 hour adding or decreasing per each pressing of "+" or "-" button. Five
seconds after setting, your desired setting will be remembered.
• Cancel ON/OFF-Timer: Press the "TIMER/TIMER" button, the number in digital window will flash
to display the present delay time of your Timer, and press this button once again to cancel the
Timer setting, also the "TIMER" light will be off; And also the second easy way to cancel the Timer
is to press the "ON/OFF" button, it will cancel the TIMER setting by force, also will turn off the unit.
Normal Sounds
Your new ice maker may make sounds that are not familiar to you. The following describes the kinds
of sounds that might be new to you and what may be making them.
• You will hear a swooshing sound when the water valve opens to fill the water tank for each cycle.
• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of
the ice maker can also make noises.
• The high-efficiency compressor may make a pulsating or high-pitched sound.
• Water running from the evaporator to the water tank may make a splashing sound.
• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your icemaker.
• You may hear air being forced over the condenser by the condenser fan. During the harvest cycle,
you may hear the sound of ice cubes falling into the ice storage bin.
• When you first start the ice maker, you may hear water running continuously. The ice maker is
programmed to run a rinse cycle before it begins to make ice.
Preparing the Ice Maker for Long Storage
• If the ice maker will not be used for a long time, or is to be moved to another place, it will be
necessary to drain out all of the water in the system. Allow all of the ice cubes have been ejected
from the evaporator of ice maker. Turn off the unit, and unplug the power cord.
• Shut off the water supply at the main water supply. Disconnect the water supply hose from the
water inlet valve. Pull out the Water drain pipe of the water tank indicating "H" in above illustration
to drain out the water in the water tank. When all of the water has been drained out, to reinstall
back the water drain pipe of the water tank.
• Then drain out all of the water from the water drain port located at unit back. Disconnect the water
drain pipe to the main drain pipeline or floor drain, plug on the drain cap again. Drop the door open
to allow for circulation and prevent mold and mildew. Leave water supply hose and power cord
disconnected until ready to reuse. Dry the interior & wipe the outside of the unit and put a plastic
bag on the unit to resist out dust & dirty.
17