Braun Multiquick 5 Gebrauchsanweisung Seite 6

5721910014_G1500_S4_42 Seite 6 Mittwoch, 26. Juni 2013 4:01 16
2
Disc
3 discs household size 5 (hole diameters 3 mm,
4.5 mm, 8 mm).
+
«Kubbe» attachment / Sausage filler
11
These attachments can be inserted instead of the disc
2 3
and the blade .
Safety fuse
If the motor switch is turned on, but the motor sud-
denly stops or does not run, the built in safety fuse
has been activated. Should this happen, turn the
switch off until the motor has cooled off (approxi-
mately 15 minutes).
If the motor will not start when switching it on again,
repeat the cooling off procedure (see above).
Put away the unit after use only after you have turned
the motor off and disconnected the plug.
Before using
All parts of the grinder attachment were covered with a
lubricating film before leaving the factory. They must be
washed before using the first time (see «Cleaning»).
Assembly
– Please note the correct assembly order of
1 5
parts - .
– The sharp side of the blade
B
– Guide the notch in the disc
E 5
in the grinder head .
– After assembling the parts
moderately tight onto the grinder head
The assembled grinder head
9
unit with a bayonet lock. Insert the metal housing into
the motor unit by holding the filling shaft of the grinder
head at an angle of 45° clockwise (the level arrow on
the grinder head must coincide with the arrow on the
motor unit) (A). Turn the grinder head anti-clockwise in
the direction of the upright arrow (A) until the filling shaft
snaps into place in an upright position (B). Place the
6
feeder tray on the filling shaft.
• In order to avoid any risk caused by the rotating
blade make sure that you only attach the grinder
5
head to the motor part after it has been completely
assembled with disc, blade and worm.
• Before attaching / replacing accessories that are in
movement during operation, switch off the appliance
and unplug it.
Operating
Turn the motor on before filling in meat, fish, vegeta-
bles, etc. To do so, press the switch
To turn the unit off, unlatch the switch by pressing
lightly.
Before processing meat, remove tendons and bones
and cut it into strips. Besides meat, the machine will
also process fish, vegetables, onions, soaked bread
rolls, boiled potatoes, stoned plums for jam. Fill the
prepared meat or vegetables into the feeder tray
push it down into the filling shaft with the pusher
Never use a fork, a spoon handle or a similar object. If
meat is crushed instead of being cut properly, please
check whether the meat grinder is assembled correctly
(e. g. whether you have perhaps over-looked inserting
one of the parts) or clean the blade
6
l
3 2
must face the disc .
2
over the protrusion
2 4 1
- , screw the cap
5
.
5
is joined to the motor
8
and let it latch.
6
and
7
.
3 2
and disc .
Notice: When processing food with high power con-
sumption – e. g. sunflower seeds mixed with oats at a
ratio of 1:3 (approximately 800 W) – do not exceed an
operating time of 10 seconds.
Before using the «Kubbe» attachment
l
filler , the meat has to be ground twice.
Cleaning
9
Wipe the motor unit with a damp cloth only and wipe
it dry. All other parts can be washed in hot water with
normal dishwashing liquids. The disc
wiped dry. Do not clean in the dishwasher.
Storage
There is a practical cord storage
unit (C).
Subject to change without notice.
Please do not dispose of the product in the
household waste at the end of its useful life.
Disposal can take place at a Braun Service
Centre or at appropriate collection points
provided in your country.
+
/ Sausage
11
2
should be
j
at the base of the