jedo NEVO Bedienungsanleitung Seite 10

USER'S MANUAL
1. Stroller unfolding/folding
- Release the safety lock of chassis before unfolding (Fig. 2).
- Unfolding of the stroller shall be enabled by pulling
the guide (handle) up while holding the chassis (Fig. 1).
When the guide is in the correct position, its blocking in
snap-in mechanism is made automatically, accompanied
by a clearly audible "click".
2. Installing and uninstalling of wheels
· Remove the plastic protectors from the axles ends of
the stroller. Protectors should be kept in order to secure
the axles when the stroller is
not used.
To remove the rear wheels, press the button located in
the centre of the wheels (Fig. 3) and remove the wheels
from the axles. To reinstall them, press the button and
slip the wheels on the axles, then release the button and
pull them towards yourself until they lock in.
- Install the10-inch front wheel (Fig.4) with forks by
inserting the axle of the forks to turntable, until you hear
a "click" meaning that the wheel is locked at the right
position.
The front wheels can be locked for the straight-ahead
position by turning the upper part of the turntable (Fig. 5)
clockwise until they click.
To remove the wheels, press the plastic button placed on
the top of turntable to the stop (Fig. 5) and pull the wheel
with the forks to the bottom.
Warning! There is grease on the wheels which can stain
the fabrics.
· Risk of suffocation: one should ensure that the plastic
protectors of the ends of axles do not fall into the child's
hands.
3. Starting of brakes up
· The stroller breaks by pressing the lateral brake pedal
(Fig. 7), so that the ends of the brake lever block the
sprocket wheel.
· Releasing of the break is enabled by pulling the brake
pedal up.
4. Installing and uninstalling of the carrycot:
Put the hood on the chassis by entering the bolts located
in its lower part into central plug mechanism of carrycot,
it will be closed automatically. (Fig. 8, 9)
To remove the carrycot from the chassis, press the red
buttons to the stop, located at the bottom, central part of
the carrycot. (This operation does not have to be carried
out simultaneously on both sides of the carrycot). Next
lift the carrycot upwards.
5. Footmuff installation
Put the footmuff on the carrycot and fasten it with the
snaps located on the sides of hood and footmuff.
6. Seat installation (travel insert):
Installing and uninstalling of the seat is the same as
carrycot.
The seat can be installed in two ways; the footboard can
be in the direction of travel or vice versa.
- Put the seat upholstery by pulling it to the seat frame,
and next fasten all the snaps.
Warning ! Before use check if the carrycot or the seat are
properly locked at the latches.
Warning ! Before using the stroller always check if the
backrest is locked properly.
7. Seat's hood installing / uninstalling
The seat has got the separate hood.
In order to place it on the walking seat, one should insert
the black holders located on the bow ends into the
plastic hooks at both sides of the seat frame/chassis.
In order to remove the hood, one should press the black
button located in its lower part and pull it up, repeat on
the other side (Fig. 11).
8. Barrier installation/uninstallation
- Place the protective barrier on the frame of the seat by
inserting it into plastic holders.
In order to remove the barrier, press the red button
located in its lower part and pull it up, repeat on the other
side (Fig. 12).
9. Installing of the foot muff
Stretch the covering on the seat and pin it with a snap.
10. Stroller assembling
- In order to put the chassis; remove the carrycot (point 4)
Next, fold the chassis by pressing the red button on the
left side of guide rail (Fig. 13) and pulling up the plastic
handles for stroller folding located on the guide rail.
In order to further reduce the stroller size, the wheels can
be removed and axles, located next
to the 12-inch wheels, by pressing the red button located
on both sides of the brake pedal (Fig. 6,7).
11. Adjusting the height of the guide rail
Simultaneously press the two black buttons located on
the guide rail, on its both sides, from inside, and moving
the guide rail properly, increase or decrease its height
(Fig. 14).
12. Setting of the footboard position
The footboard can be adjusted at three positions. Low
position (lowered): the footboard located at the horizontal
position must be pulled forward by ratchet handle
(Fig. 15a) and carefully let down.
Horizontal position: the footboard should be lifted from
the lowered position to the level, this blockade automati-
cally locks by itself.
13. Backrest adjusting
The backrest of the seat can be adjusted at four positions.
To lower the backrest, pull the plastic lever at the rear
part of the backrest (Fig. 15) and next set the correct po-
sition. To lift the backrest, it is enough to push it upward
until it reaches the correct position. It automatically locks
by itself.