Care And Maintenance; Troubleshooting - swissflex uni 11_95RF Bedienungsanleitung

Care and Maintenance
Your uni 11_95RF interactive | ambiente 11_95RF in-
teractive is a high-quality product that has been de-
signed to serve you reliably for many years to come.
For occasional cleaning and the removal of dust, we
recommend the use of a dry cloth.
Changing the batteries in the radio remote control
g Remove the cover from the battery compartment
(20) on the back of the radio remote control. Place
three AAA batteries into the compartment, paying at-
tention to the +/- markings. Close the compartment
cover again.
Changing the batteries in the uni 11_95RF interactive |
ambiente 11_95RF interactive motor control
g Disconnect the mains cable (30) from the mains
outlet before changing the batteries. Remove the cover
of the battery compartment (24) on the back of the
motor housing. Carefully remove the batteries from
the battery clips. Place two 9V block batteries into the
compartment, paying attention to the +/- markings.
Close the compartment cover again. The batteries in
the motor housing provide power in the case of a power
failure.

Troubleshooting

In case of malfunctions with your uni 11_95RF inter-
active | ambiente 11_95RF interactive, consult the
following troubleshooting tips. If the problem cannot
be resolved, disconnect the uni 11_95RF interactive |
ambiente 11_95RF interactive, from the mains outlet
and contact your Swissflex stockist.
Loss of power in the sitting position
g In the case of a power failure, the battery pack (2x 9V) in
the motor control allows you to move the bed to a slee-
ping position (horizontal position). Use the emergency lo-
wering key (23) to move the bed to the horizontal position
when there is no mains power.
After a power failure
g Before resuming use of the uni 11_95RF interactive |
ambiente 11_95RF interactive, press and hold the "All mo-
tors combined" "down" button (2), until all comfort areas
have reached the horizontal position and the motors have
stopped moving.
Activating the emergency lowering
g Press the emergency lowering button (23) on the
motor control to reach the horizontal (basic) position.
Repeated use of the emergency lowering function puts
a lot of strain on the batteries, in which case they must
be replaced.
GB
The uni 11_95RF interactive | ambiente 11_95RF in-
teractive does not work despite being switched on
and all components being connected properly
g Disconnect the mains supply unit (30) from the
mains outlet. Wait a minute and then reconnect to the
mains. If necessary, connect a bedside lamp to check
that mains voltage (230V) is present. If there is no cur-
rent, check the fuse.
g Press the "all motors combined" button "down" (2) to
reset all adjustments. The control of the uni 11_95RF |
ambiente 11_95RF contains microprocessors, so irregu-
lar power supply can lead to malfunctions.
The radio remote control does not work (The back-
ground light does not work)
g Insert (new) batteries. Where applicable, remove
any obstacles between the radio remote control and
the motor control.
Cannot programme new positions
g Repeat the programming procedure.
Programmed positions do not work
g Check whether the same position has been stored
in two different memory locations by moving the in-
dividual motors and re-programme the positions and
repeat the programming procedure.
Individual motors do not work
g Ensure the proper connection of the motor cables
to the control.
Technical data
Supply voltage: 230V / 50-60 Hz
Thrust motors: 4x 3000 N
Power rating motors: 4x 96 W
Remote control power supply: 3x AAA batteries
Radio signal range under normal conditions: 15 m
Power supply for emergency lowering:
2x 9 V block battery
Total connected load: 484 W / 6 A
Temperature range: + 5 °C to + 40 °C
Total connected load: 1440 W / 6 A
EG conformity: see last page
Operating instructions
15