Velleman VTSS5 Bedienungsanleitung Seite 4

3. Ge eneral Guid
Refer to the Velleman
Indoor
dripping
Keep th
opening
Protect
device.
• Fami iliarise yoursel
• All m modifications of
mod ifications to th
• Only y use the device
the w warranty.
• Dam mage caused by
warr ranty and the d
• Do n not switch the d
Prote ect the device
temp perature.
4. Ov verview
Refer to the illustration
1 po
2 te
3 sp
4 iro
5. Ins structions
a. Prep paration
• P Put the solderin
station. s
• Make sure the M
before you put b
• Put the solderin P
c coupling nut. O
t the coupling nu
t tighten it when
War rning: Never u
b. Elec ctrical Connec
• Connect the po C
the soldering st t
c. Tem mperature sett
• Use the rotary U
temperature. t
• S Set the temper
moments and t m
c controller [2] a
d. Ope ration
• P Prerequisite for
station. We rec s
should not be u s
Switch on the s S
temperature of t
07.12.20 010
delines
n® Service an nd Quality Wa
r use only. Ke eep this device
g liquids. Neve er put object fil
his device away y from dust an
gs are clear at all times.
this device fro om shocks and
f with the func ctions of the de
f the device are e forbidden for
e device is not t covered by th
e for its intend ded purpose. U
y disregard of c certain guidelin
dealer will not a accept respons
device on imm ediately after i
against damag ge by leaving it
ns on page 2 o of this manual.
ower cord
emperature con ntroller
ponge
on stand
s
ng iron holder [4] in the corr
sponge [3] is completely sat
it in the spong ge tray.
ng tip [5] into the shaft [6]
Only change a s soldering tip w
ut and gently p pull out the sold
necessary.
use the solde ering iron with
ction
ower cord [1] t to a 230V/50H
tation is now r eady for use.
ting
control [2] on n the front pane
rature controlle er [2] between
try to melt som me solder. If it
a little further c clockwise, wait
r clean joints is s the use of su
commend the u use of solder w
used in any cas se. Before the
soldering statio on and apply so
f 200°C (tempe erature control
VTSS5
arranty on the
away form rai
lled with liquid
nd extreme hea
abuse. Avoid
evice before ac
r safety reason
he warranty.
sing the device
nes in this man
sibility for any
it has been exp
t switched off u
5 5 bit
6 6 heating ele
7 7 antiskid rub
8 8 handle
responding hol
turated with cle
and attach it t
hen the solder
dering tip. Che
hout the sold
z power supply
el to switch the
n the second an
doesn't melt fl
t a little while a
ited solder and
with a resin flux
first uses, you
ome solder to
ler between sc
4
e last pages of this manual.
n, moisture, s plashing and
on top.
at. Make sure t the ventilation
brute force wh hen operating t
ctually using it.
ns. Damage cau used by user
e in an unauth orised way wil
nual is not cove ered by the
ensuing defect ts or problems
posed to chang ges in tempera
until it has reac ched room
ement
bber
e in the casing g of the solderi
ean water and let it drip off
o the soldering g iron with a
ring iron has co ooled down. Lo
eck the screw f fitting regularly
ering tip.
y. The power L LED turns ON a
e device on an d set the desir
nd third scale, wait a few
luidly, rotate th he temperature
and try again u until it does.
d a correct use of the solderin
x core. Halogen n containing so
should tin the e new soldering
the soldering t tip at a
cale 2 and 3). P Perfect joints a
Rev v. 02
the
l void
.
ture.
ng
oosen
y and
and
red
e
ng
older
g tip.
are
©Vellem man nv