Cleaning And Maintenance; Daily Cleaning After Completion Of The Slaughter; Disinfection; Cleaning The Splitting Saw - EFA SB295E Originalbetriebsanleitung

Cleaning and Maintenance

7.
Disconnect the unit from the
works mains before any
cleaning and maintenance
work!
Prior to starting any
maintenance, ensure that the
lids (B) are open (safety lock-
out) which will prevent the
unit from being switched on
unintentionally!
7.1 Daily cleaning after
completion of the slaughter
Trouble-free, continuous operation can be
ensured only if the splitting saw is permanently
kept in a clean, hygienic condition. The
machine should normally be disinfected before
each cleaning.
Observe the applicable safety and hygiene
regulations (EN 1672)!
Disinfectants must not be allowed to come into
direct or indirect contact with foodstuffs. Rinse
the machine with clear water after disinfection.
Do not use aggressive
solvents! Do not use steam or
high-pressure cleaners! Do
not immerse the unit in water!

7.1.1 Disinfection

Disinfect the unit during operation after every
cut with hot water (82° C).

7.1.2 Cleaning the splitting saw

After work, slacken the saw belt (see section
4.1.1 "Disassembling the saw belt" (p 6)), re-
move the saw belt, clean with hot water and
dry.
The same applies to the guide: remove after
every application and carefully clean the entire
drill hole for the holder (see section 4.2 "Saw
belt guide" (p 7).
Use a cloth, brush and warm water (40 - 55 °C)
to clean the unit. Stubborn or encrusted dirt
and residue must be soaked beforehand.
Clean using a cleaning agent, preferably as a
foam, that is applied to the surface to be
cleaned and allowed to work in for 15 - 20
minutes. Subsequently wash off the loosened
dirt manually with warm water.
Recommended cleaning agents
Schmid & Wezel

Diversey Lever Tego 2000: Surface-active
disinfectant.

Diversey Lever GmbH

Mallaufstr. 50-56, 68219 Mannheim

Alternatively:

P3-topax 91:

Surface-active disinfectant

Henkel-Ecolab Deutschland GmbH

Postfach 13 04 06, 40554 Düsseldorf
A cleaning plan and further details can be
obtained from the above company addresses
The above cleaning agents are only a
recommendation; if other cleaning agents are
used, the customer should examine the
material compatibility and the compliance with
the hygiene regulations.

7.1.3 Lubricants

Lubricants are subject to the regulations
applicable to the foodstuffs sector (DIN 1672).
Recommended lubricant for gearbox:
Klübersynth UH1 12-1600 (H1)
EFA special grease
Order No. 001 365 644 (0.8 kg)
Order No. 001 365 645 (5.0 kg)
Amount of grease requried for gearbox:
EFA SB295E and SB295EL: 600 g.
Grease recommended for all lubrication
points, guide and Tightening torque
wrench:
Molykote Longterm W2
EFA special grease
Order No. 001 365 623 (1 kg)
Order No. 001 365 624 (5 kg)
Oil recommended for oil bath of Tightening
torque wrench:
Weissöl Shell-Ondina G17, 15 Centistok / 40°
Special oil:
Order No. 001 365 611 (0.5 l)
Order No. 001 365 612 (5.0 l)
7.2 Daily maintenance of
splitting saw
In order to meet hygienic requirements, the
belt saw is to be serviced after every use.

7.2.1 Lubrication

Every time the unit is cleaned, slightly oil the
saw belt with acid-free EFA special oil sand
grease the guide with EFA grease.
Page
50 of 72
Version
11 / 2011