Technical Data; Before Starting The Equipment; Use; Operation - Scheppach BCH3300-40Li Original Bedienungsanleitung

• The battery voltage must correspond with the
battery charging voltage of the charger. Oth-
erwise, there is a risk of fire and explosion.
• Charge the batteries only in chargers that have
been recommended by the manufacturer. There
is a risk of fire if a charger for a particular type of
battery is used for another type of battery.
• The battery can be damaged by sharp objects
such as a nail or screwdriver or by external ap-
plication of force. The battery may short-circuit
and start burning, smoking, exploding or overheat-
ing.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.

6. Technical data

Nominal voltage
Speed n
0
Cutting circle diameter of line
Cutting line diameter
Weight (without battery)
Noise and vibration
The noise and vibration values were developed us-
ing a standardised measuring process.
Sound pressure L
pA
Sound power L
wA
Uncertainty K
WA
Vibration A
hv
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

7. Before starting the equipment

Unpack the device and check it for complete delivery
contents and transport damage.
NOTE
The batteries (optional; depending on the delivery
scope) are not fully charged on delivery. Before first
use, fully charge the batteries. See charger instruc-
tion manual.
Removing / inserting the battery(Fig. 2)
1. To remove the battery (3) from the appliance,
2. To insert the battery (3), place it on the guide

8. Use

Assembling the protective cover (fig. 8)
• Remove the battery.
• Turn the lawn trimmer over to access the trimmer
40 V
• Remove the pre-installed screws (1) from the trim-
6500 min
-1
330 mm
• Place the guard (2) on the trimmer head.
• Line up the screw hole on the guard with the screw
1,6 mm
2,92 kg
• Insert the screw in the trimmer head and fasten
Installing the top/bottom shaft (fig. 4)
• Insert the bottom shaft in the shaft coupling on
78,5 dB(A)
• Tighten the coupling by rotating in a clockwise di-
94,3 dB(A)
3 dB(A)
1,69 m/s²

9. Operation

1,5 m/s²
To obtain maximum performance from your grass
trimmer, please follow these instructions: (Fig. 8)
• Never use the grass trimmer without the guard.
• Do not mow grass when it is wet. The best results
• Do not allow the grass trimmer near the grass un-
• To cut properly, swing the machine sideways while
• If the grass is long, the grass must be cut shorter
• Use the guard hood to prevent unnecessary wear.
• To avoid unnecessary wear, keep the grass trim-
press the release button (13) on the battery and
pull out the battery.
track and push it back into the appliance. It will
audibly snap in.
head.
mer head with a Phillips screwdriver.
hole on the trimmer head.
the guard.
the top shaft.
rection. Make sure the top and bottom shaft parts
are screwed tight before inserting the battery again.
are achieved with dry grass.
til the switch is pressed, i.e. the grass trimmer is
in operation.
moving forwards. Keep the grass trimmer inclined
at an angle of approx. 30° while you do so .
in stages, starting from the tip.
mer away from hard objects.
GB | 21