Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Setting Up the Printer
1 INTERRUPT switch
Sets whether the PRINT button is activated to enable
interruption of the printing process and capture an image
in memory.
ON (SW-DOWN): Interrupts the printing currently
under way and prints a new picture when you press the
PRINT button during printing.
OFF (SW-UP): Disregards the fact that the PRINT
button is pressed during printing and continues the
printing currently under way.
If you press the PRINT button during printing in the
OFF mode, the alarm buzzer will sound.
2 POSTFEED switch
Sets extra blank paper once an image has been printed.
ON (SW-DOWN): Feeds out extra blank paper once an
image has been printed.
OFF (SW-UP): Does not feed out extra blank paper
once an image has been printed.
To save paper by feeding only a short length of paper
after printing an image, set this switch to OFF. In this
way, you can make more printouts per roll of paper, but
you have to feed the paper manually using the FEED
button and tear off the paper. When you make multiple
copies of the same printout, this position is effective in
helping to save paper.
3 ASPECT 4:3/1:1 switch
Normally keep this switch set to 4:3 (SW-DOWN).
When the aspect ratio of the video signal is 1:1, set it to
1:1 (SW-UP).
The printout will be longer than a printout made at 4:3.
1
5
2
2
3
3
3
5
1
3
2
3 2
3
30
0
1
2
3
4
5
6
7
8
9
30
3 4
4
3
3
3
4
4
3
275
50
4
5
5
7
3
1 3 5 7
5
4
7 5 3 1
30
3
2
10
3
7
475
2
250
4
4
3
3
3
4
4
3
30
30
3
3 2
2
5
5
3
3
3
3
2
2
1
1
4:3
4 MEMORY switch
FRAME (SW-DOWN): Normally keep this switch set
to this position.
FIELD (SW-UP): When printing fast-moving images
(such as a ball being thrown), the printout may blur. If
this happens, set the switch to this position. The printout
definition will be poorer but less blurred.
24
Preparation
1
5
2
2
3
3
3
5
1
3
2
3 2
3
0
1
2
3
4
5
6
7
8
9
30
30
3 4
4
3
3
3
4
4
3
275
50
4
5
5
7
5 4 3
1 3 5 7
7 5 3 1
30
3
2
10
3
7
475
2
250
4
4
3
3
3
3
4
4
30
30
3
3 2
2
5
5
3
3
3
3
2
2
1
1
1:1
5 DIRECTION switch
Selects whether the top or bottom of the screen is to be
printed first.
NORM (SW-DOWN): Normally keep this switch set to
this position. Printing is done from the bottom of the
screen.
REV (SW-UP): Starts printing from the top of the
screen.
1
5
2
2
3
3
3
3
2
5
1
3 2
3
0
1
2
3
4
5
6
7
8
9
30
30
3 4
4
3
3
3
4
4
3
275
50
4
5
5
7
3
4
1 3 5 7
5
7 5 3 1
30
3
2
10
3
7
475
2
250
4
4
3
3
3
4
3
4
30
30
3
3 2
2
5
5
3
3
3
3
2
2
1
1
NORM
67 SCAN switch
Sets the printout range. The printout range is
progressively widened in the NORM, WIDE 1, and
WIDE 2 order.
NORM (Switch 7, SW-UP position): Prints only the
image displayed on the standard screen size of the video
monitor.
WIDE 1 (Switch 7, SW-DOWN position): Prints
when the signal scans beyond the edge of the standard
monitor screen.
WIDE 2 ( Switch 6, SW-UP position): To further
extend the range, select this setting.
To change the printout range, set the DIP switches
according to the following table.
Scan size
DIP switch 6
NORM
SW-DOWN
WIDE 1
SW-DOWN
WIDE 2
SW-UP
Note
Do not to set both DIP switch 6 and DIP switch 7 to
SW-UP.
1
5
2
2
3
3
3
3
2
5
1
3 2
3
0
1
2
3
4
5
6
7
8
9
30
30
3 4
4
3
3
3
4
4
3
275
50
4
5
5
7
3
4
3 5 7
5
7 5 3
30
3
2
10
3
7
475
2
250
4
4
3
3
3
4
3
4
30
30
3 2
3
2
3
5
5
3
3
3
2
2
1
1
NORM
1
5
2
2
3
3
3
5
1
3
2
3 2
3
30
0
1
2
3
4
5
6
7
8
9
30
3 4
4
3
3
3
4
4
3
275
50
5
4
5
7
3
4
1 3 5 7
5
7 5 3 1
30
3
2
10
3
7
475
2
250
4
4
3
3
3
4
4
3
30
30
3
3 2
2
5
5
3
3
3
3
2
2
1
1
WIDE 1
REV
DIP switch 7
SW-UP
SW-DOWN
SW-DOWN
1
5
2
2
3
3
3
2
5
1
3
3 2
3
0
1
2
3
4
5
6
7
8
9
30
30
3 4
4
3
3
3
4
4
3
275
50
4
5
5
7
3
1 3 5 7
5
4
7 5 3 1
30
3
2
10
3
7
475
2
250
4
4
3
3
3
3
4
4
30
30
3
3 2
2
3
5
5
3
3
3
2
2
1
1
WIDE 2
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
