Adjusting Nylon Line; Replacement Of Spool; Trouble Shooting; Storing - PrimAster PM RT 600 DA Gebrauchsanweisung

Note: Periodically clean out the grass between the spool
and the guard to prevent the tool form vibrating, ensure
the line trimmer is switched off and unplugged.

8. Adjusting nylon line

Check the nylon line regularly if it is damaged or if it still
has the correct length.
When cutting performance deteriorates: Hold the run-
ning trimmer above a patch of grass. Tap the cutting
head on the ground. Note the fresh line will be advanced
only if lines are still at least 2.5 cm (1 inch) long. If the
lines are shorter: Switch off the trimmer, disconnect plug
from power supply. Press in the spool and pull end of
lines firmly outwards). If end of lines are not visible - see

(replacement of spool).

Your trimmer has a thread cutting blade that continu-
ously cuts the thread down to the appropriate length.
Note: Clean the thread cutting blade from grass re-
mainders in order to guarantee an unaffected cutting
performance.
Attention: Danger of injury through the cutting blade!
9. Replacement of spool
WARNING! Before making this change, make
sure that line trimmer is switched OFF and un-
plugged.
First, switch off and unplug the device. Wait until the
nylon thread has come to a halt. T hen push the two
locking devices 1 at the sides of the cutting head, and
remove the cutting head cover 2 (fig. 14). Remove the
used thread coil and put in the new coil 3 such, that one
end of the thread comes out of each outlet at the sides
of the cutting head (fig. 15). Please take care that the
spring 4 is properly seated under the thread coil. Finally,
close the cover by pushing it in its seat. Both locks must
properly engage.

10. Trouble shooting

• Trimmer does not work: Check power supply (e.g.
by testing on another socket or by means of a voltage
tester). Should it still not work, although the socket is
o.k., send it undismantled to an authorised service sta-
tion for repair.
• Cutting line disappears into spool: Remove spool,
pull end of line through the metal outlet and reinsert
spool. In case nylon line is used up insert a new spool
with line.
Do not make any other repairs on your own; have your
trimmer checked and repaired by an authorised dealer.
Note: The manufacturer will not be reponsible for any
damage or injuries caused by the repair of the tool by an
unauthorised person or by mishanding of the tool.

11. Storing

• Clean the unit thoroughly, especially the cooling air
slots on the motor housing.
• Do not use water to clean the device.
GB | Operating Instructions
(Fig. 12 and 13)
(Fig. 14 and 15)
• Store trimmer indoors in a dry, high or locked place
and keep out of reach of children.

12. Repair service

Repairs to electric power tools should only be carried out
by specialist electrical personnel.
13. Waste disposal and environmental pro-
tection
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection points.
Only for EU countries
Do not discard electric tools in the house-
hold waste!
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must
be collected separately for environmentally-compatible
re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the
accessory parts and auxiliary equipment without electri-
cal components accompanying the waste equipment.

14. Spare parts

Please contact our service department if you need ac-
cessories or spare parts.
When working with this machine, do not use spare parts
other than those recommended by us. Using spare parts
not recommend by us can result in serious injuries to per-
sons or damage to the machine.
The following information should be provided when
ordering spare parts:
• Type of machine
• Item number of the machine

15. Warranty

For this electric tool, the company provides the end
user - independently from the retailer's obligations re-
sulting from the purchasing contract - with the following
warranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by
the original purchasing document. For commercial use
and use for rent, the warranty period is reduced to 12
GB-7