Assembling The Vacuum Cleaner; Operation; Emptying The Dust Collector - Team ST 41 E Gebrauchsanleitung

Fax +32 2 359 95 50


ASSEMBLING THE VACUUM CLEANER

 Remove all packaging material from the appliance and its accessories.
 Insert the hose (3) in the connection inlet of the appliance (9), and press until it clicks (Fig.
1). To remove the hose, press its release buttons and pull at it.
 Assemble the handle of the flexible hose (3) on the upper part of the tube (2) and then
assemble the floor brush (1) on the other end of the tube, as indicated on figures 2 and 3.
 The floor brush (1) possesses 2 positions which allow you to clean all kinds of surfaces very
easily, simply by changing the position adequately:
Setting with the bristles inside for cleaning carpets.
Setting with the bristles outside for cleaning hard floors.

OPERATION

 First of all, check if the filters are placed properly in the appliance, as vacuum cleaning
without filter might damage the motor of the appliance irreparably (see paragraph
FILTERS for their use and installation).
 CAUTION: In order to avoid important electric disturbance when starting the appliance, it
is fitted with a "soft start" feature. This feature prevents the motor from starting at its full
power. As a result, there might be a short time-lag (1 or 2 seconds) between the moment
you press the on/off switch and the moment the appliance really starts. This is normal.
 Pull out a sufficient length of power cord and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable length. Do not extend the cable
beyond the red mark. Switch on the appliance by pressing the ON/OFF switch (8).
 You can adjust the suction power manually with the wind force adjuster (fig. 4), or with the
electronic power control switch (7). Use a low suction power for furniture and other
delicate surfaces and use high suction power for fitted carpet and other floors.
 With the accessorie supplied you can clean surfaces that are hard to reach, such as
furniture (use the crevice tool) and delicate surfaces such as curtains (use the small brush).
This accessorie can be mounted on the handle or on the tube. You can find the
accessorie on the bottom of the appliance. To store it, you just need to insert it in the
compartment foreseen to that end on the bottom of the appliance.
AFTER USE
 Stop the vacuum cleaner by depressing on the on/off switch.
 Disconnect plug from electrical outlet.
 Simply press lightly with your foot on cable rewind button on top of the cleaner. If the cord
does not enter completely in the appliance, pull 50 cm of the power cord out of the
appliance and try again.
 After use we advise you to empty the dust collector to avoid smells and mildew that could
be caused by damp dust particles that could have been vacuumed, and also to
guarantee an optimal efficiency during the next use. To do so, see below.

EMPTYING THE DUST COLLECTOR

It is necessary to remove the hose from the connection inlet first.
 Press the release button (4) on the lid of the appliance and pull open the lid. Then pull out
the dust collector (fig. 5, step 1 and 2).
 Press the unlocking button on the handle of the dust collector (fig. 5, step 3) to open the
dustcup's lower cover and spill the rubbish.
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must be reproduced and folded in order to
obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). The
pages must be folded in order to keep the good numbering
when you turn the pages of the I/B . Don't change the page
numbering. Keep the language integrity
12
Assembly page 12/31
.
TEAM ST 41 E - 080508