Product Description And Specifications; Product Features; Technical Data - Bosch GDR 18 V-160 Professional Originalbetriebsanleitung

14 | English
Safety Warnings for Impact Wrenches
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. Ensure the area is well-ventilated
and seek medical attention should you experience any ad-
verse effects. The vapours may irritate the respiratory
system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g.
against continuous intense sunlight, fire,
water and moisture. There is a risk of explo-
sion.

Technical Data

Cordless impact screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard screwdriving application according to ISO 5393
– ¼" internal hexagon
– ■ ½"
Machine screw diameter
Tool holder
1 609 92A 4PW | (25.10.2018)
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The machine is intended for driving in and loosening screws
and bolts as well as for tightening and loosening nuts within
the respective range of dimension.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Tool holder
(2) Locking sleeve
A)
(3) Battery
(4) Battery release button
(5) Rotational direction switch
(6) On/off switch
(7) "PowerLight" lamp
(8) Handle (insulated gripping surface)
(9) Screwdriver bit with ball catch
(10) Universal bit holder
(11) Screwdriver bit
(12) Application tool (e.g. screw nut)
(13) Carbon brushes
(14) Cover cap
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GDR 18 V-160
3 601 JG5 1..
V =
rpm
rpm 0 – 3600
Nm
Nm
mm M6–M14
¼" internal hexagon
A)
A)
A)
A)
A)
A)
GDX 18 V-180
3 601 JG5 2..
18
0–2800
A)
160
–
¼" internal hexagon/
Bosch Power Tools
18
0–2800
0 – 3600
A)
160
180
M6–M16
∎ ½"