Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
14 | English
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Safety information for drills and screwdrivers
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring. Cut-
ting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the op-
erator an electric shock.
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. Ensure the area is well-ventilated
and seek medical attention should you experience any ad-
verse effects. The vapours may irritate the respiratory
system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Technical data
Cordless drill/driver
Article number
Rated voltage
No-load speed
1 609 92A 4A7 | (11.10.2018)
GSR 12V-15 FC
3 601 JF6 0..
V =
10.8/12
Protect the battery against heat, e.g.
against continuous intense sunlight, fire,
water and moisture. There is a risk of explo-
sion.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal and plastic.
The power tool can be used with an angle adapter (GFA 12-
W), off-set angle adapter (GFA 12-E), bit holder adapter
(GFA 12-X) or drill chuck adapter (GFA 12-B).
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Tool holder
(2) Torque presetting ring
(3) Gear selector switch
(4) Battery release button (2x)
(5) Battery
(6) Rotational direction switch
(7) On/off switch
(8) Battery charge indicator
(9) Worklight
(10) Bit holder adapter GFA 12-X
(11) Drill chuck adapter GFA 12-B
(12) Off-set angle adapter GFA 12-E
(13) Angle adapter GFA 12-W
(14) Locking ring
(15) Handle (insulated gripping surface)
(16) Universal bit holder
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GFA 12-X
GFA 12-B
–
–
–
–
A)
A)
A)
A)
A)
GFA 12-E
GFA 12-W
–
–
Bosch Power Tools
–
–
Werbung
Inhaltsverzeichnis
