Components Required For Operation; Intended Use; Operating Principle; Preparation - B. Braun Aesculap Bonum Gebrauchsanweisung/Technische Beschreibung

2.2

Components required for operation

■
Bonum battery operated clipping machine
■
Charger
■
Mains power cord (with device plug)
■
Li-ion battery
2.3

Intended use

Bonum battery operated clipping machine
The Bonum battery-operated clipping machine is used for clipping large
animals such as cattle, horses and large dogs.
Charger GT643 (LC40)/Li-Ion battery GT641 (3INR19/66-1)
The GT643 (LC40) charger is used to charge the GT641 (3INR19/66-1) lith-
ium ion battery.
2.4

Operating principle

Bonum battery operated clipping machine
The Bonum battery-operated clipping machine is switched on and off
using the on/off button 20.
Charger GT643 (LC40)/ Li-Ion battery GT641 (3INR19/66-1)
The GT643 (LC40) charger is designed for a mains voltage range of 220 V
to 240 V and 50 Hz to 60 Hz.
To ready the GT643 (LC40) charger for operation, connect it to mains
power by plugging in the mains plug.
The GT643 (LC40) charger has one charging bay.
Charging starts automatically as soon as the Li-Ion battery is inserted in
the charging station.
The charging time depends on the charge state and capacity of the Li-ion
battery.
Charging principle
The Li-ion batteries are charged by constant current pulses.
The charge state of the Li-ion battery is monitored during charging. Mon-
itoring of the charging curve ensures that the battery is fully charged
without overcharging.
When the Li-Ion battery is completely charged, the LED, operation
indicator d lights up continuously.
The Li-Ion battery 21 can remain in the charger 22 and is then always
ready for operation.
Additionally, the battery temperature and charging time are monitored as
well.
Charging time
Charging is stopped as soon as the maximum charging time is reached. The
charging time is approx. 53 min.
3.

Preparation

Non-compliance with the following instructions will preclude all respon-
sibility and liability in this respect on the part of Aesculap.
►
When setting up and operating the product, adhere to:
– national regulations for installation and operation,
– the national regulations on fire and explosion protection,
– operating advisories according to IEC-/VDE regulations.
4
4. Working with the battery-operated
clipping machine, charger and Li-ion
battery
4.1

System set-up

Connecting the accessories
Combinations of accessories that are not mentioned in the present
instructions for use may only be employed if they are specifically intended
for the respective application, and if they do not compromise the perfor-
mance and safety characteristics of the products.
4.2

Function checks

Bonum battery operated clipping machine
►
Carry out a visual inspection.
►
Push Li-ion battery 21 into the machine bay until it clicks into place.
Charger/Li-ion battery
►
Carry out a visual inspection.
►
Prior to connecting the product to mains power:
– Check the mains power cord for any damage.
– Inspect product for possible damage (e.g. inspect contacts of the
charging bay for bent contacts)
►
Plug in the mains plug at the mains power socket.
►
Place the Li-ion battery 21 in the charging bay of the charger and
charge it, see Fig. F.
4.3 Connecting the charger/Charging the Li-ion bat-
tery
Fire hazard due to battery poles
shorted by fluids or metal compo-
WARNING
nents!
Li-ion battery not inserted
►
Risk of injury due to damaged mains
power cord!
WARNING
Check mains power cord for any
►
damage before charging.
Arrange for any damaged mains
►
power cord to be replaced by the
manufacturer.
Risk of injury and material damage
due to damaged Li-ion battery!
WARNING
Prior to charging, check the Li-ion
►
battery for any damage.
Do not use or charge any damaged
►
Li-ion batteries.