Weather Forecast; Programming The Alarm - Unitec Climate W101 Bedienungsanleitung

INSERTING THE BATTERIES
Open the battery compartment  on the back of
the device, insert 2 AAA batteries with the indicated
polarity; close the battery compartment again.
Note:
Only use the same or a similar type of battery as
those recommended by the manufacturer. Only bat-
teries with the same charging capacity may be used.
°C/°F SELECTION
Press the "-" key 6 to switch between the °C and °F
display.
SETTING UP THE BAROMETER:
As soon as the weather station is supplied with
power, it shows the air pressure, based on the local
elevation. To increase the accuracy, adapt the eleva-
tion as follows:
1) Press the [BARO ] key 7 for 3 seconds
2) The air pressure display (J) "0" starts to flash
3) Using the keys [+] 8 and [-] 9, enter the approxi-
mate elevation (in 10-meter steps).
4) Press the [BARO] 7 key again to end programming.
Note:
The unit of the air pressure display can be changed
in standard mode with the [+] key 8.
sunny
SETTING THE DATE AND TIME
1) Keep the [SET] key 4 pressed until the year flashes
in the time display (C).
2) The value can be increased or decreased with the
keys [+] 5 and [-] 6.
3) Press the [SET] key 4 again to adjust the month, as
described above.
4) Press the [SET] key 4 again to set the date.
5) Press the [SET] key 4 again to adjust the hours.
6) Press the [SET] key 4 again to enter the minutes.
7) Press the [SET] key 4 again to select the 12 or
24 hour display.
8) Press the [SET] key 4 again to specify the time
difference in relation to a second local time
(e.g. London +1)
313526_Manual_140114.indd 7
partly cloudy

WEATHER FORECAST

The device predicts the weather conditions for the
next 12 – 24 hours, based on changes in the atmos-
pheric pressure. The area of coverage is approx. 30
– 50 km. The weather forecast is based on changes
in the atmospheric pressure and provides 70 – 75%
correct predictions. As weather conditions cannot
be predicted with 100 percent accuracy, we cannot
be held responsible for losses caused by incorrect
forecasts.
Note:
Locations with different geography, such as e.g. inland
areas or coastal areas, have different weather forecasts.
If your weather forecast shows continuously rainy or
stormy weather over a prolonged period of time and
does not reflect the actual weather, the weather forecast
accuracy must be fine-tuned as follows:
1) Check the actual weather conditions outside
2) Adapt the elevation (J) as described under "SETTING
UP THE BAROMETER". The elevation can be adjusted
in 10 m steps; then exit the mode. Repeat this step until
the weather forecast icon matches the actual weather
situation outside. (E.g.: If the weather outside is partly
cloudy, change the elevation setting until the weather
forecast icon shows "partly cloudy".)
cloudy wet

PROGRAMMING THE ALARM

1) Keep the [AL] key 3 pressed until the hour starts
flashing in the time display (C).
2) The value can be increased or decreased with the
keys [+] 5 and [-] 6.
3) Press the [AL] key 3 again, to set the minutes.
4) Press the [AL] key 3 again, to complete the
programming.
5) The alarm can be activated and deactivated in normal
mode with the [+] key 5.
SNOOZE FUNCTION
When the alarm goes off, it can be delayed by a further
eight minutes with the [SNOOZE] key 1. During the
delay time the alarm icon
key 3 again, not [SNOOZE] 1, to stop the alarm for a
day.
7
stormy (flashing)
(D) flashes. Press the [AL]
English
18.02.14 10:25