Connecting The Stove; Setting Up The Pecan Eco; Mounting The Soapstone On The Pecan Eco S And Pecan Eco M; Assembly Of The Pecan Eco L - WANDERS Pecan Eco Serie Bedienungsanleitung Und Montagevorschriften

Pecan Eco S

Connecting the stove

The Pecan Eco is a heavy wood stove. Depending on the version, the Pecan Eco weighs at least 300 kilos, including the
2-meter long smoke-gas discharge. Make sure the wall or floor that you are installing the stove on can easily carry this weight.
Before installing the stove, follow the directions in the previous chapter 'Preparation' . Protect your back and the floor during
installation.

Setting up the Pecan Eco:

All images can be found on page 55.
1. Check the packaging, is there any visible damage? If so, report it.
2. Pull the wood-burning stove out of the box (use the correct lifting procedures and take care not to injure your back).
3. Carefully put the fireplace in the right place, directly under the flue.
4. Ensure the fireplace is level.
5. The underpressure in the flue must be 10 to 12 Pa (0.1 to 0.12 mBar).
6. Take any fire-protective measures that may be necessary (see page 23 "Fire Safety").
7. Now install the flue. Use a suitable flue with a diameter of 150 mm and a thickness of at least 2 mm. Remember, a flue can
expand by up to 1 cm per meter; so ensure the flue is not fitted too tight.
8. The steel front plate above the door can be removed for convenience. This is held in place with 4 magnets. 2 pin/hole
connections ensure the plate does not sag (see fig. 01).

Mounting the soapstone on the Pecan Eco S and Pecan Eco M:

All images can be found on page 55.
1. Check the packaging, is there any visible damage? If so, report it.
2. Take the soapstone panels out of the box (use the correct lifting procedures and take care not to injure your back).
3. Place the lower side stones into position. A pin on the bottom plate of the wood-burning stove ensures the stone
remains in place (see fig. 02).
4. Screw the headless Allen bolt into the connection. This bolt will be the connection pin for the second stone (see fig. 03).
5. Place the second stone into position and attach it, also using a headless Allen bolt. Ensure the Allen bolt is screwed in far
enough to ensure it does not touch the stones above (see fig. 04).
6. The upper mounting clamp can be adjusted by loosening the 2 bolts in the slotted holes (see fig. 04a).
7. Gently place the 2 upper stones into position on top of the wood-burning stove (see fig 05).

Assembly of the Pecan Eco L:

All images can be found on page 55 and 56.
The Pecan Eco L is based on the M version of the wood-burning stove. A height extender is put in place as described below.
First follow the steps for setting up the Pecan Eco M as described above.
1. Check the packaging, is there any visible damage? If so, report it.
2. Remove the height extender set from the packaging. This consists of a rack and a front plate (see fig. 06).
3. Remove the steel front plate above the door. This is held in place with magnets (see fig. 07).
4. Remove the upper mounting clamps for the soapstone from the wood-burning stove and attach them to the top of the
height extender set (see fig. 08).
5. Put the height extender in place on the wood-burning stove. It does not have to be screwed in place (see fig. 09).
6. Remove the middle mounting clamps used for the soapstone from the wood-burning stove and re-attach them in the
Ø 80 mm
Pecan Eco M | Pecan Eco L
GB
Ø 80 mm
25