Sony PMW-F3 Bedienungsanleitung Seite 4

• Limiter status displayed for the zoom position indication on the
LCD monitor/viewfinder screen
Major functions updated with V1.31
3D-Link
3D shooting with 3D-Link and a power zoom lens is enabled
(optional CBK-3DL01 3D-Link Option, 3D-Link cable, and SCL-
Z18X140 power zoom lens are required):
• Linking function of the lens position (zoom, iris, and focus) on
the main unit and sub unit, either constant linking or temporary
linking enabled
• Iris offset adjustable when the lenses on both units are linked to
move in sync
Restrictions
• Status indication of the lens condition (zoom, iris, etc.) on the
main unit and that on the sub unit may not be the same even
after the lens positions on both units have been synchronized.
• If Iris Position Sync, Focus Position Sync, or Zoom Position
Sync under 3D-Link of the OTHERS menu is set to On for
constant linking, pressing the assignable button to which the
corresponding linking function is assigned does not activate
temporary linking. Set the constant linking function to Off for
activating the temporary linking.
• The linking function of this unit does not guarantee
synchronizing in the same phase.
S-Log
S-Log422 shooting is enabled (optional CBK-RGB01 RGB&S-LOG
Output Option is required):
• 1.5G YPbPr422 & S-Log and 3G YPbPr422 & S-Log options
available under Dual-Link & Gamma Select of the VIDEO SET
menu
Synchro Rec (synchronized recording)
Synchronized recording via Dual-Link output enabled for normal
recording (a recording device supporting Synchro Rec and Dual-
Link output signals is required):
• Synchro Rec option under SDI Rec Control available
Restrictions
If Synchro Rec is started when the i.Link output or the Picture
Cache Recording is active, or during playback (including Rec
Review and thumbnail display), recording synchronization may
not be achieved or distorted video recording may occur.
Wide-angle manual zoom lens
(An optional SCL-P11X15 wide-angle zoom lens is required.)
Status indication to observe the lens condition is enabled.
MF Assist setting
The default setting for MF Assist of the CAMERA SET menu has
been changed to Off.
Major functions updated with V1.2
3D-Link
3D shooting with 3D-Link is enabled (optional CBK-3DL01
3D-Link Option and 3D-Link cable is required):
• Genlock/TC sync
• Recording operation in synchronization
• Copying (from a main unit to a sub unit) of camera settings
• Special recording operations (Interval Recording, Frame
Recording, Slow & Quick Motion Recording)
• Synchronized Rec Review on two camcorders
• Sensitivity adjustment independently for each ND filter to
eliminate the difference between two units
S-Log EI mode
S-Log shooting by adjusting the MLUT gain is enabled (optional
CBK-RGB01 RGB&S-LOG Output Option is required):
• Gain adjustment in the range of 800EI (equivalent to 0 dB) to
3200EI (equivalent to 12 dB)
• Instant switching of MLUT on/off by assigning the function to a
button
Power zoom lens
Shooting with various effective lens operations using a power
zoom lens is enabled (optional SCL-Z18X140 power zoom lens is
required):
• Zoom operation using the servo zoom lever and assignable
buttons on the PMW-F3 and the infrared remote commander
(supplied)
• Auto focus operation
• Auto iris operation
• Iris operation from an external control device, such as a remote
control unit (Refer to the Supplement supplied with the
PMW-F3.)
• Status indication to observe the lens conditions (zoom, focus,
iris, etc.)
• Steady Shot function
Lens with the ARRI connector
Status indication of the lens condition (iris) is enabled. (Refer to
"Attaching a Lens" in the Operating Instructions.)
Preset White adjustments
The following adjustments are enabled:
• Preset white adjustment for S-Log outputs (Optional CBK-RGB01
RGB&S-LOG Output Option is required.)
• Offset adjustment (R/B channels) for preset white (3200K)
Menu scroll
In addition to the conventional scrolling method, cyclical
scrolling is enabled for menu selection.
Other status indications
The following selections become available:
• On/off of the Rec 2 indication
MLUT data
Adding MLUT data to the conventional camera data, collective
storage and readout of the camera settings and MLUT data are
enabled (optional CBK-RGB01 RGB&S-LOG Output Option is
required).
Histogram indication
Histogram indication (vertically reduced in the viewfinder with
the previous versions) is improved.
Major functions updated with V1.1
Clip names
User-specified characters can be displayed (MP4/AVI).
Planning metadata
Shooting with planning metadata is possible.
• Planning metadata can be read from recording media inserted
into a memory card slot.
• The planning metadata to be read can be selected.
• Clip names based on names defined in planning metadata can
be specified.
• Clip names can be specified in languages other than English.
• More shot marks can be added.
• Shot mark names can be specified in languages other than
English.
• Shooting information can be reflected in planning metadata.
• Information contained in planning metadata can be viewed.