Installation Instructions; Unpacking; Product Description; Preparations For Installation - Bosch TR2500TO 5 T Montage- Und Gebrauchsanleitung

Please read this installation and operating instruction manual
carefully, then act accordingly! Store for future reference.
2

Installation instructions

2.1

Unpacking

• Inspect the new appliance for transport damage!
• Please dispose of the packaging, and if applicable, the old appliance
in an environmentally-friendly manner.
Scope of delivery (Fig. 1)
1 Appliance with operating panel
2 Installation bracket
3 Mounting (2 screws, 2 wall plugs)
4 Documentation
2.2

Product description

The small water heater is only suitable for open (unpressurised)
installation. It heats and stores drinking water up to approx. 85 °C.
Different temperature levels can be selected with the temperature
selector knob.
The appliance may not be operated with pre-heated water, as otherwise
the safety temperature limitation will trip.
The appliance is connected using the mains plug.
3

Preparations for installation

• Shut off the water supply before connecting the appliance.
Do not insert the mains plug.
• Remove the installation bracket on the appliance and break off the
retaining rings (A).
• Fix the connection cable to the rear of the appliance to suit the
required length (B).
Wall mounting (Fig. 2)
• Align the appliance on the wall and use the three indents (top, left and
right on the appliance) to apply markings (C).
• Connect the markings by a pattern of crossed lines with a spirit level
(D1 and D2).
• Place the installation bracket on top at the point of intersection of the
drawn lines and mark the position for the holes (E).
• Drill the holes and insert wall plugs (F1).
• Attach the installation bracket (notch at top) to the wall using the
screws (F2).
• Suspend the appliance in the installation bracket (F3).
3.1

Exchanging appliances (Fig. 3)

When replacing an old small water heater with this new appliance, the
existing drill holes with wall plugs can be used. Please note that the new
appliance is approx. 2 cm higher.
If the new appliance is to be flush at the top like the old appliance (G1):
• Attach the new installation bracket to the wall with the notches
at the top.
If the new appliance is to be flush at the bottom like the old appliance (G2):
• Turn the installation bracket around and attach to the wall with the
notches at the bottom.
Water connection (Fig. 4)
CAUTION:
Caution!
The existing fitting may not be covered with scaling.
TR2500TO – 6 720 876 011 (2017/06)
• Do not grease the thread!
Info: Replacement for damaged threaded nozzles available from
customer service.
• Fit the taps if required (A1 and A2).
• Insert the seals (B1).
• Ensure the axial fit of the connection pipes in the nozzles.
• Place the union nuts on the thread and tighten them by hand (B2).
• Tighten the screw fitting (C). Counter the threaded nozzles on the
warm water heater with a wrench.
• After the unit has been used to heat water a few times, retighten
the screw fitting.
• Set the flow to 5 l/min (= 1 l in 12 seconds) on the corner valve.
3.2

First start-up

3.2.1

Electrical connection

• Important: Do not insert the plug into the mains socket yet.
• Fill the appliance with water first. Water must flow from the fitting.
• Only then insert the plug into the mains socket.
Note: If the appliance is not filled with water, the resettable safety
temperature limitation will trip!
3.2.2

Checking the heating

• Turn the rotary selector switch to "3" (approx. 85 °C).
• Monitor the heating process until the pilot lamp switches off after
approx. 12‒18 minutes.
• Check the temperature.
CAUTION:
Caution:
If the safety temperature limitation has switched off the small water
heater, unplug the mains plug, open the warm water tap and allow
approx. 4 litres of water to flow. Then plug the mains plug back in.
The appliance is ready again for operation.
3.2.3

Limitation of the water temperature

The temperature of the water leaving the tap for the small water heater
can be mechanically set to stage "1" (approx. 38 °C) or stage "eco"
(approx. 60 °C) (see "Operation", page 8).
Conserving energy
• Set the rotary selector to "eco" to conserve energy.
• Hand over the installation and operating instructions to the user and
explain how the appliance operates.
Installation instructions
7