Operating Instructions - Ritter solida 4 Gebrauchsanleitung

English
Unfold the illustrations at the
front and back of this manual.
Please read these instructions
thoroughly before you start to
use the appliance. Keep these
operating instructions in a safe
place and ensure that they are
included with the appliance if
passing it on to a third party.
INTENDED uSE
The multi slicer is used for the
slicing of household foods.
If the appliance is used for a
purpose other than this, or if it
is operated incorrectly, severe
injuries may occur or the
appliance may be damaged.
All warranty and liability claims
will be rendered null and void in
this case.
INITIAL START-up
preparation
Remove the appliance carefully
from the packaging. Remove
all packaging parts and keep
these together with the packag­
ing in a safe place. Clean the
appliance before allowing it to
come into contact with any food
(see CLEANING).
Setting up the appliance
• Set the appliance down on a
flat, non-skid surface close to a
mains socket.
solida
4
Slide the slice carriage (3)
into the guide grooves on the
appliance.
solida
5
Using a small amount of force,
push the slice carriage (3)
vertically into the guide groove
on the appliance until it audibly
locks into place.
Slide the left­over holder (2)
onto the slice carriage's handle.
10
Unwind the mains cable (8)
to the length required from the
cable compartment (9) under
the appliance and insert the
mains plug into the socket.
SLICING
Use the slice thickness
adjustment knob (12) to set the
required thickness.
Note:
The slice thickness adjustment
scale is not a millimetre scale.
For safety reasons, the "0"
position is designed to cover
the blade.
Place the food to be sliced
onto the slice carriage (3). Use
the left­over holder (2) to press
it up against the stop plate (1).
Protect your hands, by
always using the slice carriage
and, where applicable, the left­
over holder. Exception: Exces­
sively large foods to be sliced.
• Switch the appliance on
using the rocker switch (7). Two
operating modes are available:
Temporary operation (Posi­
tion II):
The rotary blade (13) runs as
long as the switch is pressed
and held down in this position.
Continuous operation (Posi­
tion I):
The rotary blade runs without
the switch being pressed and
held down until you move the
switch to the "0" position.
Note:
Never use the appliance for
more than a maximum of
5 minutes in continuous opera-
tion.
• With the appliance running,
gently feed the food to be sliced
into the path of the rotary blade.
• When finished slicing, wait
until the rotary blade has come
to a complete stop.
• After each use, turn the slice
thickness adjustment knob
to the "0" position, in order to
cover up the sharp rotating
blade and to avoid any injuries.
CLEANING
Caution:
Switch the appliance off
before cleaning it; pull the
mains plug out off the socket
and turn the slice thickness
adjustment knob (12) to the
"0" position.
Clean the multi slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent
its surface from rusting.
Note:
Over time, an accumulation of
food residue may cause dam-
age to the surface of the rotary
blade, causing it to rust.
preparation
• Remove the slice tray (11)
and the left­over holder (2).
solida
4
Press the release button (4)
and pull the slice carriage (3)
off the appliance.
solida
5
Pull the slice carriage (3) for­
ward and then lift it up and out
of the guide groove.
Removing the rotary blade:
Remove the blade
guard (6).
Open the blade catch (5),
by turning it in a clockwise
direction.
• Remove the blade catch.
• Take hold of the rotary
blade (13) at its rotational cen­
tre and remove it.