SSS Siedle BFCV 850-0 Produktinformation Seite 7

English
Deluxe handsfree bus telephone
intercom with colour monitor for
Siedle In-Home bus
Functions:
• Calling, hands-free/simplex com-
munication, video, door release and
storey call
• Speech/control button
• Colour monitor 8.8 cm (3.5")
• Integrated video memory for
28 pictures, memory upgrade pos-
sible using an SD card
• Door release and light button
• Buttons for switching and control
functions
• Internal speech communication
• Display of switching statuses
• Muting button for call tone
• 11 ring tones
• Call volume adjustable in 5 steps
• Speech volume adjustable 5 steps
• Monitor button for current picture
• 5-way button for video memory
and zoom function
• Video memory function (only with
additional installation)
Intercom functions:
• Call forwarding
• Internal group call
• Internal call with callback function
• Collective announcement
• Automatic call pick-up with
internal call
• Doormatic
The intercom functions can only be
programmed using the bus program-
ming software BPS 650-... .
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of delivery
• BFCV 850-... (Base plate and
housing with circuit board)
• Dummy card for SD card slot
• Operating instructions for the
end user
• This product information
Mounting
Strip back cable to appr. 80 mm.
1 Recommended mounting height
appr. 1.50 m to centre device.
2 Open the device from the back;
by releasing the base plate with the
locking lever.
3 When mounting directly on the
wall, fasten the base plate using
4 screws, paying attention that
the plate is the right way up (top
marking). When mounting on a
switch box, use the screw openings
in the centre of the device, paying
attention that the plate is the right
way up (top marking).
4 Install in accordance with the
wiring diagram. The cores of the
installation cable must be stored
inside the free installation space in
the base plate.
5 Hook the housing into the base
plate from above and close by
exerting a slight pressure. Depending
on the installation environment, it
may be necessary to change the
microphone sensitivity of the
BFCV 850-... in order to permit clear
speech transmission. If a speech con-
nection exists, press the door release
button and light button simultane-
ously. Using the speech button
+/- the microphone sensitivity can
be set. If no input is made within
10 seconds, the microphone setting
switches off again.
Save the set microphone sensitivity
by pressing the muting button for 3
seconds.
Dismantling
6 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board
remains in the housing superstruc-
ture.
Lettering
7 The lettering panel can be
inscribed to indicate the button
functions. The see-through panel
can be lifted at the side.
Terminal assignment
TaM/TbM Input In-Home bus
TaM/TbM Throughput In-Home bus
ERT/ETb Storey call button
+M/-M Additional supply
20–30 V DC for video
memory function and
door parallel call
S1/S1 Potential-free contact for
additional bell
Commissioning
Installation, commissioning and
programming are described in the
system manual (enclosed with line
rectifiers BNG/BVNG 650-... ).
Note
As in the as-delivered / de-energized
status, the contact position of the
bistable relay (contact S1/S1) cannot
be defined, the bus supply to the
device must be connected before-
hand to ensure that the bistable
relay functions correctly.
Accessories for BFCV 850-...
ZTCV 850-... table-top accessory for
conversion from a wall-mounted to
a table-top device.
5