Relationship Between The Video Input Signal And Monitor Output According To The Video Convert Mode Settings Of Main Zone - Denon AVC-A1XV Bedienungsanleitung

System Setup
• It is not possible to down-convert from HDMI and DVI-D input
signals to the component, S-Video or composite video monitor
output terminals.
• Video down conversion to the MAIN ZONE's monitor output is only
possible when the component video input resolution is 480i
(interlaced standard definition video – NTSC format, for North
America) or 576i (interlaced standard definition video – PAL format,
for Europe and other countries).
• Set the resolution of the video output to one that is compatible with
the resolution of your monitor.
• When "Component" is set at "Scaler" under "HDMI/Component
Out", the signals are output to the HDMI/DVI-D monitor output
terminal with their original resolution. Use a monitor compatible with
a resolution of 480i/576i.
¢ The analog video to HDMI conversion function
• The AVC-A1XV's video up-conversion function lets you output
analog video input signals (component – 480i/576i, 480p/576p,
1080i or 720p; S-Video and composite video - 480i/576i) to the
HDMI monitor output terminal.
• With the AVC-A1XV, the resolution of the signal output to the
HDMI MONITOR OUT terminal can be selected (
resolutions with which the monitor is compatible can be checked
using < STATUS > or [ON SCREEN].
• If you do not want to use the function for converting analog video
signals to HDMI signals, select "OFF" for "Analog to HDMI
Convert" at "Setting the HDMI/Component Out" (
In this case, the function for video up conversion to the component
video terminal operates.
Relationship between the video input signal and monitor output according to the video convert mode
settings of MAIN ZONE
Video convert
HDMI
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
E E
ON
C C
C C
C C
C C
page 6). The
C C
C C
C C
C C
C C
C C
C C
C C
page 6).
C C
C C
C C
C C
C C : Signal input
E E : No signal
480p ~ 720p : 480p/576p/1080i/720p
•
The MAIN ZONE video conversion function is compatible with the following
format: NTSC, PAL, SECAM, NTSC4.43, PAL-N, PAL-M and PAL-60.
•
When SECAM signals of video input are up-converted, the signals are
output in PAL format from the S-Video connector.
•
When the input signal is set to component video 1080p, the signals cannot
be output to the HDMI monitor output terminal.
Input signals
COMPONENT S-VIDEO VIDEO
E E E E E E
E E E E C C
E E C C E E
E E C C C C
C C (1080p) E E E E
C C (480p ~ 720p) E E E E COMPONENT
C C (480i/576i) E E E E COMPONENT
C C (1080p) E E C C
COMPONENT ✳1
C C (480p ~ 720p) E E C C
COMPONENT ✳1
C C (480i/576i) E E C C
C C (1080p) C C E E
COMPONENT ✳2
C C (480p ~ 720p) C C E E
COMPONENT ✳2
C C (480i/576i) C C E E
C C (1080p) C C C C
COMPONENT ✳2
C C (480p ~ 720p) C C C C
COMPONENT ✳2
C C (480i/576i) C C C C
E E E E E E
E E E E C C
E E C C E E
E E C C C C
C C (1080p) E E E E
C C (480p ~ 720p) E E E E
C C (480i/576i) E E E E
C C (1080p) E E C C
C C (480p ~ 720p) E E C C
C C (480i/576i) E E C C
C C (1080p) C C E E
C C (480p ~ 720p) C C E E
C C (480i/576i) C C E E
C C (1080p) C C C C
C C (480p ~ 720p) C C C C
C C (480i/576i) C C C C
E E
✳1
✳2
✳3
•
HDMI MONITOR OUT:
When there is no HDMI input signal and "HDMI" is selected for the "Scaler"
setting, the signal is output as set with the "Resolution" setting.
When "Component" is selected for the "Scaler" setting, the signal is output with
the same resolution as the input signal.
• COMPONENT MONITOR OUT:
When "Component" is selected for the "Scaler" setting, the signal is output as
4
set with the "Resolution" setting. However, the output resolution is limited to a
maximum of 480p/576p if the input signal is copyright-protected.
ENGLISH
MONITOR OUT
HDMI COMPONENT S-VIDEO
E E E E E E
VIDEO VIDEO VIDEO
S-VIDEO S-VIDEO S-VIDEO
S-VIDEO S-VIDEO S-VIDEO
E E COMPONENT E E
COMPONENT E E
COMPONENT COMPONENT
COMPONENT ✳1
VIDEO VIDEO
COMPONENT ✳1
VIDEO
COMPONENT ✳1 ✳1
COMPONENT
COMPONENT ✳2
S-VIDEO S-VIDEO
COMPONENT ✳2
S-VIDEO
COMPONENT ✳2
S-VIDEO
COMPONENT ✳2
S-VIDEO S-VIDEO
COMPONENT ✳2
S-VIDEO
COMPONENT ✳2
S-VIDEO
HDMI E E E E
✳2
HDMI VIDEO VIDEO
✳2
HDMI S-VIDEO S-VIDEO
✳2
S-VIDEO
HDMI S-VIDEO
HDMI COMPONENT E E
HDMI COMPONENT E E
HDMI COMPONENT COMPONENT
✳1 COMPONENT ✳1
HDMI VIDEO
✳1 COMPONENT ✳1 ✳3
HDMI VIDEO
✳1 COMPONENT ✳1 ✳1
HDMI COMPONENT
✳2 COMPONENT ✳2
HDMI S-VIDEO
✳2 COMPONENT ✳2
HDMI S-VIDEO
✳2 COMPONENT ✳2
HDMI S-VIDEO
✳2 COMPONENT ✳2
HDMI
S-VIDEO
✳2 COMPONENT ✳2
HDMI
S-VIDEO
✳2 COMPONENT ✳2
HDMI S-VIDEO
: Not output
: On screen display superimposed on video signal and output.
: On screen display superimposed on S-Video signal and output.
: Video signals are not output when the analog to HDMI convert function is
set to "ON".
: On screen display only displayed for SYSTEM SETUP, SURROUND
PARAMETER and [ON SCREEN].
: When "OFF" is selected for the "Analog to HDMI Convert" setting, no
video signals other than the HDMI input signal are output.
: Including the contents of and above.
ENGLISH
System Setup
VIDEO
E E
VIDEO
S-VIDEO
S-VIDEO
E E
E E
COMPONENT
VIDEO
✳3
VIDEO
VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
E E
VIDEO
S-VIDEO
S-VIDEO
E E
E E
COMPONENT
VIDEO
VIDEO
VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO