Setting The Speaker Mode; Adjusting The Balance; System Functions - Denon PMA-201SA Bedienungsanleitung

ENGLISH

[3] Setting the speaker mode

ON / TA DBY ¡ FF MODE OU CE D RE T
PH NES FU CT ON
2 1
STOP PLAY VOLUME
/SELECT
PRESET
+
2
-
TAPE
SLEEP FUNCT ON MODE
1
Press the MODE button to display "SPEAKER".
• The mode switches as shown at the left each
time the button is pressed.
1
MODE MODE
(Main unit) (remote control unit)
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
SELECT
FUNCTION
(OFF) (ON)
2
(OFF)
(Main unit) (remote control unit)
• To set to "ON":
Turn the dial clockwise (,) or press the
button.
To set to "OFF":
Turn the dial counterclockwise .) or press
H
the button.
10

[4] Adjusting the balance

VOLUME
ON / TA DBY ¡ OFF MODE
PH NES FU CT ON
NTEG ATED AMPL F ER PMA 01 A
2 1
STOP PLAY VOLUME
SELECT
PRESET
+
-
TAPE
SLEEP FUNCT ON MODE
Press the MODE button to display "BALANCE".
MODE
1
(Main unit)
• The mode switches as shown at the left each
time the button is pressed.
✻ "BALANCE" cannot be selected when the
source direct mode is on.
E ther turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
(ON)
(right
(left channel channel
volume volume
FUNCTION
adjustment) adjustment)
D
(Main unit)
2
• If the volume of the right speaker is low:
Turn the dial clockwise (,) or press the
button.
If the volume of the left speaker is low:
Turn the dial counterclockwise .) or press
H
the button.
• The balance can be set to "CENTER" or
adjusted within the range of +1 to +10 in
steps of 1. When set "CENTER", the
difference between the volume of the left and
right speakers is 0.
9

SYSTEM FUNCTIONS

2 Operation is even easier when the components in the 201SA series are connected to the PMA-201SA with system
connections. (For instructions on connections, refer to "CONNECTIONS" on page 5, 6.)
2 All the system function signals for operating the components in the 201SA series are output from the PMA-201SA,
VOLUME
so be sure to connect the PMA-201SA when making system connections.
SOU CE D RE T
2 The system functions will only work when the components of the 201SA series are connected. They will not work
with other components.
NTE RATED AMP IF ER PMA 201 A
2 When system connections are made, the system functions descr bed below can be used.
(1) The system remote cont ol unit (RC-906) included with the PMA-201SA can be used to perform the main
operations on the other components.
(2) The remote cont ol signals of the other components are received by the PMA-201SA's remote sensor.
(3) Auto power on function:
When the system is set to the standby mode, the power turns on automatically when the PLAY/PAUSE button
2
( 1 3 ) on the CD player (DCD-201SA), cassette deck (DRR-201SA), and MD recorder (DMD-201SA) is pressed,
and playback begins. In addition, if one of the preset buttons (PRESET UP or DOWN) on the tuner TU-201SA) is
1
pressed, the tuner's power turns on and the radio p ogram is tuned in.
(4) Auto function selection:
The function automatically switches when the PLAY/PAUSE button ( 1 3 ) on the CD player (DCD-201SA),
cassette deck (DRR-201SA), and MD recorder (DMD-201SA) is pressed, and playback begins.
MODE
5) CD synchronized recording:
CDs can be recorded on the cassette deck (DRR-201SA), MD recorder (DMD-201SA) simply by pressing the CD
SRS button on the cassette deck.
(remote control unit)
6) Simultaneous recording:
When the PLAY/PAUSE button ( 1 3 ) on the CD player (DCD-201SA) is pressed while the cassette deck (DRR-
201SA), MD recorder (DMD-201SA) is set to the recording pause mode, recording starts automatically.
(7) Timer functions:
The timer functions on the tuner (TU-201SA) can be used to start playback or record radio programs ("air check")
at set times. The sleep timer can also be used.
2 For instructions on the various operations, refer to the components' operating instructions.
(left channel
VOLUME
/SELECT
volume
adjustment)
(right
channel
volume
(remote
adjustment)
control unit)
D