List Of Components - Zummo Z14 Bedienungsanleitung

The display shows
message Error
The display shows
message Error and a
flashing Icon.
Blade breaks
Not enough juice is
being extracted from the
fruit
Hooper is not delivering
fruits so the squeezing
area
Hooper is delivering
several oranges at the
same time into the
squeezing area
For any advice or to request spare parts, you should state the model and serial number

6.7. LIST OF COMPONENTS

0504001A SX-50 CUÑAT REDUCER
0504002B 0.33CV, 225-50Hz MOTOR
0504003A TWO-PHASE 0.33CV 240/250V-50Hz MOTOR
0504003B TWO-PHASE 0.33CV 115V-60Hz MOTOR
0504003C TWO-PHASE 0.33CV 220V-60Hz MOTOR
0504004A 16XL MOTOR PULLEY
0504005 REDUCER INPUT PULLEY (60XL037)
0504007 PIN WASHER AND REDUCER PIN
0504013 THRUST PANEL PIN
0504014N-1 CUP GUIDE WITH INSERT
0504019 BELT 190XL 0.37
0504024 CUPS ALIGNMENT ADJUSTMENT PAD
0504026 SX-50 REDUCER OUTPUT SHAFT
0505010A FASTENING NUT WITH RAKED JOINT
0505010A-1 CUP NUT
0505010A-2
FASTENING NUT JOIN 20x3.2
0506006/1 TRAY MICRO SPRING
0506007 SHORT MICROMETER
0506008 LONG MICROMETER
0506010 POWER CORD
26
Casing not fitted correctly (Disp. 5). (Fig. 7)
Hopper Track not fitted correctly. (Disp. 5)
Tray not assembled or incorrectly assembled (Disp. 6). (Fig.8a-8b)
Disp. 5 Disp. 6
Check if the fruit is frozen.
Check for piled-up fruit peels inside the Juice tray.
Check if Balls are correctly tightened
Check to see if the orange peels are stuck to the inside of the Cups.
Check if components of different squeezing sets are mixed
To unblock the machine, use the 5mm Allen key located at the right of the
lower vent. Insert it into the hole on the right side and, with the machine
switched off, turn clockwise until the cups are raised, removing the
obstruction. WARNING: Make sure the Allen key is removed before
switching the machine on.
The Peel Extracting Bands are loose or broken and peels are piling up in
the Juice tray.
Cup nuts are too loose.
Balls are loose.
(Z14 Model) The low-pass filter is missing.
(Self-service model) The ball washers (which are placed underneath the
balls) are missing.
Fruit peel is too thin. Place one extra washer under each ball.
Fruit is too big for the Fruit Classifiler in use.
Fruit is too small for the Fruit Classifier in use.
Hopper not properly assembled. See section nº 12 of this manual.
of your machine (Fig. 2).
0506011
0506014
0506015
0506021
0506022
0506026
0506026-1
0506027
0506028
0506036
0508013
10/21
10/25
10/28
1009069
1011028
1401A00
1401B00
1402001
1402002
FUSE 5x20 6,3A
ELECTRICAL PLUG WITH FUSES
BLACK BIPOLAR SWITCH
ZUMMITO PLATE BUSHING
FUSE SUPPORT 5X20 UL
FUSE HOLDER CAP
FUSE HOLDER FLANGE
PLASTIC CAP Ø17,3
WIRE PRESS
POWER CORD
RUBBER SUPPORT 85mm
CONDENSER 30µF (MOTOR 230V)
CONDENSER 100µF (MOTOR 115V)
CONDENSER 22µF (MOTOR 240V)
MAGNETIC SENSOR
LEVER MICROSWITCH 60g.
CASING UNIT
CASING CLOSURE
FRONT
CUP GUIDE COVER