Philips Innergize HB 935 Bedienungsanleitung Seite 7

Setting the time for a tanning or relax session.
1 Check the chapters 'Tanning sessions: how often and how long?' and 'Relax sessions: how often and how long?' for the correct tanning
or relaxing time.
2 Set the time of the tanning or relax session by pushing the + button to put the time forward or by pushing the - button to put the time
backward (fig. 16).
Keep the button pressed in to adjust the time more quickly.
3 Lie down directly under the lamp unit of the appliance.
4 Always wear the protective goggles provided if you are taking a tanning session.
Switch on the tanning lamps or the infrared lamps by pressing the start button ∞ (fig. 17).
5
It can take a few seconds for the lamps to go on.This is normal.
B
A blinking dot will appear and the set time will be shown on the display (25 minutes in this case) (fig. 18).
The countdown of the set tanning or relax time will now start.
During the last minute of the session you will hear a beeping sound.
During this minute, you can press the pause/repeat button § to repeat the set time (fig. 19).
The display shows the set time and starts to count down.The beeping stops.
It is also possible to set a new time during the last minute.
By doing this, you can avoid the 3-minute waiting time which is necessary to allow the tanning lamps to cool down after they have been
switched off.
This waiting time does not apply to the infrared lamps.
Set a new time by pushing the ¢ or £ buttons.Then push the start button ∞ (fig. 20).
6
The beeping stops and the time that has just been set starts counting down.
When you do not repeat the session by pressing § or set a new time during the last minute of the session, the countdown continues
and the appliance will automatically switch off as soon as the set time has passed.
Interrupting the tanning or relax session
You can interrupt the tanning session by pushing the pause/repeat § button (fig. 21).
1
The lamps will be switched off, ¶ appears in the display together with the remaining time. For 3 minutes the remaining time will blink. During this
time the lamps cool down.When the blinking has stopped, you can switch the appliance back on again by pushing the ∞ button.The remaining
time will now be counted down.
You can interrupt the relax session by pushing the pause/repeat § button (fig. 22).
2
The lamps will be switched off, P appears in the display together with the remaining time (not blinking).The waiting time does not apply to the
infrared lamps, so you can switch the appliance back on immediately by pushing the ∞ button.The remaining time will be counted down.
Changing the tanning or relax time during a session
When you are tanning, you can change the set time by pushing the ∞ button.The lamps will be switched off.Then set a new time by
1
pushing the ¢ £ buttons.Wait until the set time has stopped blinking (this will take 3 minutes because the lamps have to cool down
first) and push the ∞ button again (fig. 23).
When relaxing Ç, you can change the set time by pushing the ∞ button.The lamps will be switched off.You can set a new time and
2
switch the appliance back on immediately by pushing the ∞ button.The waiting time does not apply to the infrared lamps (the newly set
time does not blink on the display).
Natural fragrances
During tanning or relaxing you can enjoy your favourite fragrance.You can choose from three different fragrances.
The scent granules have been specially developed for use in this appliance. Do not use other granules.
Filling the cartridge
1 Remove the cap of the cartridge by pulling while applying pressure in the small pressing points (fig. 24).
2 Open the package at the small opening at the top.
3 Fill the cartridge with the content of one whole package of scent granules.
4 Close the cartridge by putting the cap back onto it.You will hear a click.
Placing or removing the cartridge
1 Place the cartridge in the holder. It only fits in one way and locks in place with a click (fig. 25).
To remove the cartridge, place your thumb and index finger on the sides of the cartridge. Remove the cartridge from the holder by
pressing on the disc (fig. 26).
Setting the fragrance level
1 You can set the fragrance level by turning the cartridge (fig. 27).
Turn the cartridge in the direction of the large flower symbol to increase the fragrance level and turn it in the opposite direction to reduce the
fragrance level.
2 When you store the appliance or do not want it to emit a fragrance, turn the cartridge away from the large flower symbol as far as it
goes (fig. 28).
The holes will no longer be visible.
3 Replace the granules when the cartridge no longer emits any fragrance. Replacement packages with 3 sachets of scent granules are
available under type number HB080.
ENGLISH
7