Technical Data; Attachment And Operation - Scheppach LB2500P Originalanleitung

6. Technical data

LB2500P
Technical data
Dimension LxWxH mm
Air speed max. km/h
air volume min./max.
m /min
3
dust bag capacity l
Power unit
Displacement cm3
Max. engine output kW
Idle speed min-1
Fuel tank capicity
cm3
Engine type 2-stroke engine, air-cooled
Weight kg
Subject to technical changes!
Information concerning noise
according to relevant standards:
Sound pressure L = 97,0 dB(A)
pA
Sound power L = 108,4 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration
Lower handle A = 15,1 m/s
2
hv
Upper handle A = 11,92 m/s
2
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this sign:

7. Attachment and operation

ATTENTION! Before working on the device - cleaning,
inspection, maintenance or other work - always turn off
the device.
ASSEMBLY
The blower must not be used or switched on until
it has been fully assembled.
Assembly(Fig7-9)
• Remove the screw (K) and its washers (L).
• Align the first blower tube(4) compartment with the
protrusion of the air outlet, push the tube and turn it
1050x250x350
268
12
-
25,4
0,7
3500 ± 300
0,65
4,7
emission measured
90° clockwise, in order to permanently fix it in place.
• Fix the tube (4) to the air outlet using the screw (K)
and its washers (L).
• Align the second blower tube(5) compartment with the
protrusion (P) of the first tube, push the tube and turn
it 90° clockwise, in order to permanently fix it in place.
Warning! Use only original manufacturer's replace-
ment parts, accessories and attachments. Failure to
do so can cause poor performance, possible injury and
may void your warranty. Never use the machine wit-
hout the guard assembled!
Operation
Before starting
Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that the
safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special 2-stro-
ke engine oil. Mix the fuel mixture as indicated in the fuel
mixing table.
Important: Do not use a fuel mixture which has been
stored for longer than 90 days.
Important: Never use 2-stroke oil with a recommended
mixing ratio of 100:1. The manufacturer's warranty
will be voided in case of engine damage due to inade-
quate lubrication.
Important: Only use containers designed and approved
for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil into
the mixing bottle (see scale printed on the bottle). Then
shake the bottle well.
Never use oil for 4-cycle engine or use water cooled
2-cycle engine. It can cause spark plug fouling exhaust
part blocking or piston ring sticking.
Mixed fuels, which have been left unused for a period of
one month or more, may clog the carburetor or result in
the engine foiling to operate property. Put remained fuel
into an airtight container and keep it in the dark and cool
room.
Fuel mixing table
Mixing procedure: 40 parts petrol to 1 part oil
Example:
1 l Petrol : 0,025 l 2-stroke oil
5 l Petrol : 0,125 l 2-stroke oil
Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Take care of fire!
GB 21