Performing An Application (Fig. A) - DeWalt D25333 Übersetzt Von Den Originalanweisungen

EngLIsh
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. A, D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
with the other hand on the side handle
Operation Modes (Fig. A)

WARNING: Do not select the operating mode when the
tool is running.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
symbol Mode
Rotary Drilling
Rotary
hammering
hammering
only
to select an operating mode:
1. Depress the mode selector release button
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding with the desired mode.
nOtE: The mode selector 3 must be in rotary drilling, rotary
hammering or hammering only mode at all times. There are no
operable positions in between. It may be necessary to briefly
run the motor after having changed from 'hammering only' to
'rotary' modes in order to align the gears.

Performing an Application (Fig. A)


WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood "back-
up" block to prevent damage to the material.

WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
22
6 ,
.
5
3 to select the
application
Screwdriving
Drilling into steel, wood
and plastics
Drilling into concrete and
masonry
Light chipping
4 .
1. Choose and install the appropriate chuck, adapter, and/or
bit onto to the tool. Refer to Bit and Bit Holders.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle 5 as required.
4. Place the bit/chisel on the desired location.
5. Select the direction of rotation using the forward/reverse
slider 2 . When changing the position of the control slider,
be sure the trigger is released.
a. Push the forward/reverse slider
forward (RH) rotation. See arrows on tool.
b. Push the forward/reverse slider
reverse (LH) rotation.

WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
6. Depress the trigger switch
the trigger switch, the faster the tool will operate. For
maximum tool life, use variable speed only for starting holes
or fasteners.

WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Various types of SDS-Plus drill bits and chisels are available as
an option. Accessories and attachments used must be regularly
lubricated around the SDS-Plus fitment.
Consult your dealer for further information on the
appropriate accessories.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
3 , select the mode
2 to the LH-side for
2 to the RH-side for
1 . The farther you depress