Makita PW5000C Bedienungsanleitung Seite 5

accessory. Pinching or snagging causes rapid stalling of
the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the operator,
depending on direction of the wheel's movement at the
point of pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades create
frequent kickback and loss of control
Safety Warnings Specific for Stone Polishing
Operations:
a) Do not use excessively oversized abrasive
disc. Follow manufacturers recommendations,
when selecting abrasive disc. Larger abrasive
disc extending beyond the pad presents a
laceration hazard and may cause snagging, tearing
of the disc or kickback.
Additional safety warnings:
16. Do not leave the tool running. Operate the tool
only when hand-held.
17. Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
18. Check that
supported.
19. Pay attention that the wheel continues to
rotate after the tool is switched off.
the workpiece is
20. Do not use the tool on any materials
containing asbestos.
21. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become
disconnect the tool from the mains supply
( use non metallic objects ) and avoid
damaging internal parts.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
Important Notes about Mains
Connection for 110 Volts, 50-60Hz
Caution:
Read and observe these precautions before using
the tool. Non-observance of these precautions may
lead to personal injuries and damage to the tool!
The tool was built according to the European
Standards
motor-driven power tools; here in particular section
of power
EN60309-2 (plugs, receptacles and couplings for
industrial
standards, the earth contact position of the plug-in
device may only be carried out in "12 o'clock
position".
The tool has a plug-in device with a "12 o'clock"
earth contact position.
However, since the European Standard EN60309-2
does not provide a differentiation regarding the
supply voltage and this earth contact position, there
is the possibility to confuse the connection to an
isolating transformer with another output voltage
(e.g. 230 V). When connecting the tool to an isolating
transformer, make absolutely sure to use the correct
output voltage (110 V, 50 - 60 Hz).
This tool is designed exclusively for connection to
an isolating transformer with an output voltage of
110 V. Due to its use in wet conditions (water
connection on the tool), this tool must never be
connected to a power supply without an isolating
transformer.
Damages caused by inappropriate tampering with
the plug-in device are not subject to warranty or
legal guarantee claims.
properly
Contact your specialist supplier for an isolating
transformer suitable for your tool.
5
necessary to
EN60745-1 (safety
tools with water
applications). When
clear dust, first
of hand-held,
connection) and
applying these