Operation - Makita RP1800 Bedienungsanleitung

ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the tool.
Installing or removing the bit
Fig.7
CAUTION:
Install the bit securely. Always use only the wrench
•
provided with the tool. A loose or overtightened bit
can be dangerous.
Use always a collet which is suitable for the shank
•
diameter of the bit.
Do not tighten the collet nut without inserting a bit or
•
install small shank bits without using a collet sleeve.
Either can lead to breakage of the collet cone.
Use only router bits of which the maximum speed,
•
as indicated on the bit, does exceed the maximum
speed of the router.
Insert the bit all the way into the collet cone. Press the
shaft lock to keep the shaft stationary and use the wrench
to tighten the collet nut securely. When using router bits
with smaller shank diameter, first insert the appropriate
collet sleeve into the collet cone, then install the bit as
described above.
To remove the bit, follow the installation procedure in
reverse.

OPERATION

CAUTION:
Before operation, always make sure that the tool
•
body automatically rises to the upper limit and the
bit does not protrude from the tool base when the
lock lever is loosened.
Before operation, always make sure that the chip
•
deflector is installed properly.
Fig.8
Always use both grips and firmly hold the tool by both
grips during operations.
Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Lower the tool body and
move the tool forward over the workpiece surface,
keeping the tool base flush and advancing smoothly until
the cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction.
1
2
3
1. Workpiece
2. Bit revolving direction
3. View from the top of the tool
4. Feed direction
001984
NOTE:
Moving the tool forward too fast may cause a poor
•
quality of cut, or damage to the bit or motor. Moving
the tool forward too slowly may burn and mar the
cut. The proper feed rate will depend on the bit size,
the kind of workpiece and depth of cut. Before
beginning the cut on the actual workpiece, it is
advisable to make a sample cut on a piece of scrap
lumber. This will show exactly how the cut will look
as well as enable you to check dimensions.
When using the straight guide or the trimmer guide,
•
be sure to install it on the right side in the feed
direction. This will help to keep it flush with the side
of the workpiece.
Fig.9
Straight guide
Fig.10
The straight guide is effectively used for straight cuts
when chamfering or grooving.
Install the straight guide on the guide holder with the
clamping screw (B). Insert the guide holder into the holes
in the tool base and tighten the clamping screw (A). To
adjust the distance between the bit and the straight guide,
loosen the clamping screw (B) and turn the fine adjusting
screw (1.5 mm per turn). At the desired distance, tighten
the clamping screw (B) to secure the straight guide in
place.
Fig.11
Wider straight guide of desired dimensions may be made
by using the convenient holes in the guide to bolt on extra
pieces of wood.
Fig.12
When using a large diameter bit, attach pieces of wood to
the straight guide which have a thickness of more than
15 mm to prevent the bit from striking the straight guide.
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
If the distance between the side of the workpiece and the
cutting position is too wide for the straight guide, or if the
side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight
board to the workpiece and use it as a guide against the
trimmer base. Feed the tool in the direction of the arrow.
10
2
4
4