Herunterladen Inhalt Inhalt Diese Seite drucken

ROWENTA PRO PERFECT Gebrauchsanleitung Seite 11

Vorschau ausblenden Andere Handbücher für PRO PERFECT:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 18
IS THERE A PROBLEM ?
Problems
The steam generator does not
switch on or the iron indicator
and ON/OFF indicator do not
switch on.
Water runs through the holes in
the soleplate.
White streaks come through the
holes in the soleplate.
Brown streaks come through
the holes in the soleplate and
stain the linen.
The soleplate is dirty or brown
and my stain the linen.
There is no steam.
There is little steam.
Water streaks appear on the
linen.
The red "removable water tank
empty" light is on.
Steam escapes from the scale
collector valve.
Steam escapes under the
appliance.
The scale collector light stays
on.
HELPLINE
If you have any product problems or queries with your product, please telephone our
Customer Relations team on:
0845 602 1454 (UK) - (01) 677 4003 (Ireland)
Consult our web site: www.rowenta.co.uk
ENVIRONMENT PROTECTION FIRST !
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste disposal centre.
Possible causes
The appliance is not switched on.
You are using the steam control
button before the iron is hot
enough.
You are using the TURBO steam
control too often.
Water has condensed in the pipes
because you are using steam for
the first time or you have not
used it for some time.
Your boiler has a build-up of
scale because it has not been
rinsed out regularly.
You are using chemical descaling
agents or additives in the water
for ironing.
Your linen is not rinsed
sufficiently or you have ironed a
new garment before washing it.
You are ironing at too high
temperature.
You're linen is not rinsed sufficiently
or you are using starch.
The water tank is empty (water
tank empty light (f) is lit).
The steam output control dial is
set at minimum.
The soleplate temperature is set
to the maximum.
When taking a break from
ironing, if your ironing board
cover is soaked with water it is
not suited to the power of a
steam generator.
You have not pressed the
"Restart" button.
The water tank is not correctly
fitted into position.
The scale collector valve has not
been tightened correctly.
The scale collector valve is
damaged.
The generator is faulty.
The generator is faulty.
You have not pressed the restart
button after descaling.
7
Solutions
Check that your appliance is correctly plugged in and
press the illuminated on/off switch (on the front of the
base-unit).
Decrease the steam output while ironing at low
temperature (steam output control dial on the control
panel).
Wait for the thermostat light to go out before
activating the steam control button.
Press the TURBO steam control 2 or 3 times.
Press the steam control on the iron away from the
ironing board until steam comes out of the iron.
Rinse the collector when the "Calc-Away System"
indicator flashes. If your water is very hard, rinse it
more often.
Never add this type of product in the water tank or in
the boiler (see our recommendations regarding water
to be used).
Ensure linen is rinsed thoroughly to remove any soap
deposits or chemicals on new garments which have
been sucked up by the iron.
See our recommendations regarding temperature
control setting.
Ensure linen is rinsed thoroughly and always spray
starch on the reverse side of the fabric to be ironed.
Fill the water tank and press the "Restart" button on
the control panel.
Increase the steam output (control dial on the control
panel).
The generator is working but steam is very hot and
dry. As a consequence, it is less visible.
Check that your ironing board is suitable. A mesh type
ironing board must be used to allow any excess steam
to escape and to avoid steam venting sideways.
Check there is water in the water tank.
Press the "Restart" button on the control panel.
Push it into position until it "clicks" into place.
Tighten the scale collector correctly.
Contact an Approved Service Centre to order a new
scale collector valve.
Do not use the steam generator and contact an
Approved Service Centre.
Do not use the steam generator and contact an
Approved Service Centre.
Press the restart button on the control panel.
EN

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Pro perfect dg8860

Inhaltsverzeichnis