10. Appendix; 10.1. Help With Problems; Specifications Hcw 80; 10.3. Specifications Hc60Ng - Honeywell HCW 80 Montage Und Bedienung

10. Appendix

10.1. Help with problems

Problem Cause
Teach-in failed Batteries
inserted
incorrectly
Radio
connection
failure
HC60NG does HC60NG
not react to set and
point changes HCW 80 not
on HCW 80 teached-in
After teach-in Teach-in
red LED is on procedure
and green LED incorrect/
is flashing once incomplete
every 3 sec
Position of
HCW 80
incorrect
Red LED of the Communi-
HC60NG is on cation loss
RF signal
blocked
Batteries of
HCW 80
exhausted
HC60NG
and
HCW 80 not
teached-in

10.2. Specifications HCW 80

Batteries 1.5 V, type LR06, AA
Frequency 868.3 MHz (transmitter)
Operating temperature 0 °C to 50 °C
Storage temperature –20 °C to 70 °C
Humidity 5 % to 90 % relative humidity
IP class 30

10.3. Specifications HC60NG

Electrical
Receiver power supply 230 V AC (+10 %, –15 %), 50 Hz
Switch type SPDT potential free
Output rating 24–230 V AC, 10 A resistive,
3 A inductive, 0.6 p.f.
Wire access From the rear (wall box mounting),
(receiver only) right an bottom
Remedy
Insert the batteries
►
correctly.
Eliminate interference
►
sources (metal, wireless
devices).
Correct installation site.
►
Repeat the teach-in.
►
Reset HC60NG.
►
Follow the teach-in
►
procedure as described
in section 5.
Repeat the teach-in.
►
Repeat the teach-in
►
keeping approx. 1 m
distance between
HCW 80 and HC60NG.
Relocate the HCW 80
►
(see section 3.2).
Replace batteries in
►
HCW 80
(see section 9).
Follow the teach-in
►
procedure as described
in section 5.
RF
RF operation band ISM (868.0–868.6) MHz,
1 % duty cycle
RF communication 30 m in a residential building
range environment
RF communication Short, high rate transmissions to
technology minimise air time and avoid
collisions
Blocking immunity Receiver class 2 (ETSI EN300
220-1 version 1.3.1)
RF binding method Factory pre-bound with the room
unit HCW 80 (kit Y6630D1007
only)
Environmental & Standard
Operating temperature 0 to 40 °C when relay load <8 A
0 to 30 °C when relay load >8 A
Shipping & storage –20 to 55 °C
temperature
Humidity Humidity range 0 to 90 % rh,
non-condensing
IP class 30
Meeting the following EN 60730-1 (1995), EN 55014-1
standards (1997), EN 55014-2 (1996), ETSI
EN 300 220-3 (2000), ETSI
EN 301 489-3 (2000)
10.4. Device and function definition in
accordance with EN 60730-1
• Purpose of the device is temperature controlling
• Device fulfills protection class 2
• Independently installable electronic control system with
fixed installation
• Type of action is type 1.8
• Temperature of ball thrust hardness test for housing
components 75 °C and for live parts such as, for
example, terminals 125 °C
• EMC emitted interference test at 230 V∼, 50 HZ
maximum
• Pollution degree is 2
• Rated voltage is 4000 V (corresponding to overvoltage
category III)
• Software class is A
10.5. WEEE directive 2002/96/EC – Waste
Electrical and Electronic Equipment
directive
At the end of the product life dispose of
►
the packaging and product in a
corresponding recycling centre.
Do not dispose of the unit with the usual
►
domestic refuse.
Do not burn the product.
►
Appendix
11