Installing The Software - Synq DLP6 Bedienungsanleitung

ENGLISH
to unlock it (display on the right appears):
 Turn the DIAL (4) to select a character and press the NEXT button (6) to set the next character, ...
 When the password is entered, press the ENTER button (11) to confirm.
 IF THE PROCESSOR IS NOT LOCKED: you will have 4 different ways to lock the processor:
 Locktype = Modify
All parameters and settings are visible but you can't change them without
introducing a password first. Only the mute switches can be used:
 Turn the DIAL (4) until the display on the right is shown.
 Press the ENTER button (11)  you will be asked to set a password.
 Turn the DIAL (4) to select a character and press the NEXT button (6) to set
the next character, ... (maximum 8 characters – DON'T forget it !!!)
 When the password is entered, press the ENTER button (11) to confirm.
Remark: if you don't want to set a password, simply leave it blank.
 Locktype = Modify & View
You can't see or change parameters and settings without introducing a
password first. Only the mute switches can be used:
 Turn the DIAL (4) until the display on the right is shown.
 Press the ENTER button (11)  you will be asked to set a password.
 Turn the DIAL (4) to select a character and press the NEXT button (6) to set
the next character, ... (maximum 8 characters – DON'T forget it !!!)
 When the password is entered, press the ENTER button (11) to confirm.
Remark: if you don't want to set a password, simply leave it blank.
 Locktype = Modify & Mute
All parameters and settings are visible but you can't change them without
introducing a password first. Also the mute switches are locked:
 Turn the DIAL (4) until the display on the right is shown.
 Press the ENTER button (11)  you will be asked to set a password.
 Turn the DIAL (4) to select a character and press the NEXT button (6 to set
the next character, ... (maximum 8 characters – DON'T forget it !!!)
 When the password is entered, press the ENTER button (11) to confirm.
Remark: if you don't want to set a password, simply leave it blank.
 Locktype = Everything
You can't see or change parameters and settings without introducing a
password first. Also the mute switches are locked:
 Turn the DIAL (4) until the display on the right is shown.
 Press the ENTER button (11)  you will be asked to set a password.
 Turn the DIAL (4) to select a character and press the NEXT button (6) to set
the next character, ... (maximum 8 characters – DON'T forget it !!!)
 When the password is entered, press the ENTER button (11) to confirm.
Remark: if you don't want to set a password, simply leave it blank.
WARNING!  don't forget your password, write it down in a safe place.
The password CAN NOT be recovered if forgotten or lost!!!
MAIN MENU – CONFIG:
In a big setup more than one processor can be used and interconnected with the
RS-485 connections on the rear panel (15). To identify each processor, they all
need a unique device ID.
This is how you can change the device ID:
 Press the DIAL (4) until the first display on the right is shown.
 Press the NEXT button (6) until the display shows "CONFIG"
 Press the ENTER button (11) to enter the submenu.
 Turn the DIAL (4) to change the Device ID number (116, actual ID is marked
with an asterisk "*")
 Press the ENTER button (11) to confirm.
SYNQ
®
OPERATION MANUAL
9/96
ENGLISH
MAIN MENU – DUMP PROGRAM:
It is possible to copy the user programs from a "master" unit [network cable connected to RS-485 output (15)]
to one or more "slave" units [network cable connected to RS-485 input (15)] At the same time you should set
the master and slave units so communication is possible (read the next point "RECEIVE DUMP" also before
you start!)
This is how you prepare the master unit:
 Press the DIAL (4) until the first display on the right is shown.
 Press the NEXT button (6) until the display shows "DUMP PROGRAM"
 Press the ENTER button (11) to enter the submenu.
 The display asks "Are you sure?" and proposes "NO"
 Turn the DIAL (4) to change the "NO" to "YES" if you want to send a dump.
NOW WAIT and prepare the slaves first (see next point) before you continue!
 Press the ENTER button (11) to confirm  The master starts dumping all programs. If an error occurs The
display shows "ERR".
Remark: the dumping process can't be interrupted. When the dump is finished the master returns to normal
working mode.
MAIN MENU – RECEIVE DUMP:
It is possible to copy the user programs from a "master" unit [network cable connected to RS-485 output (15)]
to one or more "slave" units [network cable connected to RS-485 input (15)] At the same time you should set
the master and slave units so communication is possible (read the previous point "DUMP PROGRAM" also
before you start!)
This is how you prepare the slave unit:
 Press the DIAL (4) until the first display on the right is shown.
 Press the NEXT button (6) until the display shows "RECEIVE DUMP"
 Press the ENTER button (11) to start the receiving process, the display shows
"RECEIVING DUMP" while the unit is waiting for the master.
NOW you can start the DUMP program on the master!
Remark: press the RECALL button (7) if you want to interrupt the process.
When the dump is finished the slave returns to normal working mode.
PC SOFTWARE
Our personal favorite because it's so much faster! The PC-software is so easy to use that it doesn't need a
lot of explanation. If you are familiar with the use of all parameters than you can use it right away, we will just
give you some basic explanations. You can connect the DLP-6 in two different ways to your PC:
 Via USB: This is the easiest way but the length of your cable is limited to only
5m. Use a standard USB-cable to connect the USB-slot on the rear of the
DLP-6 to one of the USB-slots of your PC.
 Via RS485: This is a little more complicated but the length of your cable can
be extended to 100m. You will need the supplied RS485/USB converter (see
picture). Connect one side of a standard straight CAT-5E network cable to one
of the RS-485 connectors on the rear of the DLP-6. Connect the other side of
the network cable to the RJ-45 input of the RS485/USB converter and insert it
in a free USB-slot on your PC.

INSTALLING THE SOFTWARE:

Very important: before you install the Windows
USB or RS485 communication!
 Part1 – installing the USB driver
AUTOMATIC installation:
 First connect the DLP-6 with your PC (via USB or RS485) and switch the DLP-6 on.
 Windows will detect new hardware and ask you if it can search and install a driver via internet: accept
this option. Windows will try to install the driver automatically. After some time windows will inform you
if it could install the driver or not.
 Proceed with the manual driver installation if the driver could not be found and installed.
DLP-6 SYNQ
®
OPERATION MANUAL
®
software you should install a driver to ensure the
10/96 DLP-6