Product Description And Specifications; Intended Use; Product Features - Bosch EasyHeat 500 Originalbetriebsanleitung

OBJ_BUCH-3137-001.book Page 10 Tuesday, November 28, 2017 9:26 AM
10 | English
 Be careful when working with the
power tool. The power tool produces
intense heat which can lead to in-
creased danger of fire and explosion.
 Exercise special care when working close to inflamma-
ble materials. The hot air jet or the hot nozzle can ignite
dust or gases.
 Do not operate or work with the power tool in areas
where there is danger of explosion.
 Never direct the hot air jet at the same position for
longer periods. Easily inflammable gases can develop
e.g., when working plastic, paint, varnish or similar mate-
rials.
 Be aware that heat can be conducted to hidden covered
materials and can ignite them.
 Safely place the power tool on the storage surfaces
after use and let it cool completely before packing it
away. The hot nozzle can cause damage.
 Do not leave the switched-on power tool unattended.
 Store idle power tools out of the reach of children. Do
not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Do not expose the power tool to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
 Always wear safety goggles. Safety goggles will reduce
the risk of injuries.
 Disconnect the plug from the socket outlet before mak-
ing any adjustments, changing accessories, or placing
the power tool aside. This safety measure prevents unin-
tentional starting of the power tool.
 Check the power tool, cord and plug each time before
use. Do not use the power tool if damage is determined.
Do not open the power tool yourself and have it ser-
viced only by a qualified repair person using only origi-
nal spare parts. Damaged power tools, cords and plugs in-
crease the risk of electric shock.
Provide for good ventilation of your
working place. Gas and vapour developing
during working are often harmful to one's
health.
 Wear safety gloves and do not touch the hot nozzle.
Danger of burning.
 Never direct the hot air jet against persons or animals.
1 609 92A 3U2 | (28.11.17)
 Do not use the power tool as a hairdryer. The hot air be-
ing blown out is significantly hotter than that from a hair-
dryer.
 When operating the power tool in damp environments
is unavoidable, use a residual current device (RCD).
The use of a residual current device (RCD) reduces the risk
of an electric shock.
 Do not allow foreign objects to enter the power tool.
 The distance between the nozzle and the workpiece de-
pends on the material you are working on (metal, plas-
tic etc.) and the intended working method. Always test
the amount of air and temperature first.
 Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications

Intended Use

The power tool is intended for stripping coats of paint, thaw-
ing water pipes, bending plastic, melting adhesive bonding,
killing weeds and heating shrink tubing. The power tool is in-
tended to be operated by hand.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Standing surface
2 On/off switch and power settings
3 Nozzle
4 Heat shield, removable (UniversalHeat 600)
5 Wide jet nozzle*
6 Glass protection nozzle*
7 Angle nozzle*
8 Reflector nozzle*
9 Reduction nozzle*
10 Heat-shrinkable sleeve*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Bosch Power Tools