Specifications - Makita 2414NB Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Base
1-2. Bolt holes
2-1. Lock button / Lock-off button
2-2. Switch trigger
3-1. Screw
3-2. Spark guard
4-1. Socket wrench
4-2. Guide plate
4-3. Move
4-4. Hex bolts
6-1. Socket wrench
6-2. Guide plate
6-3. Hex bolts
7-1. Shaft lock
7-2. Safety guard

SPECIFICATIONS

No load speed (min
Dimensions (L x W x H)
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in ferrous materials with
appropriate abrasive cut-off wheel. Follow all laws and
regulations regarding dust and work area health and
safety in your country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.26 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
Explanation of general view
7-3. Socket wrench
8-1. O-ring
8-2. Inner flange
8-3. Ring
8-4. Spindle
8-5. Cut-off wheel
8-6. Outer flange
8-7. Hex bolt
9-1. Vise plate
9-2. Vise nut
9-3. Vise handle
10-1. Spacer block
11-1. Guide plate
11-2. Straight piece of wood (Spacer)
11-3. Over 45 mm long
Model
Wheel diameter
Hole diameter
-1
)
With under cover
With European type safety guard and under cover
Safety class
ENE007-3
Noise
The typical A-weighted noise level determined according
to EN61029:
Sound pressure level (L
Sound power level (L
ENF002-2
Uncertainty (K) : 3 dB(A)
Vibration
The vibration total value (tri-axial vector sum) determined
ENF100-1
according to EN61029:
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
4
11-4. Over 65 mm long
11-5. Over 190 mm long
12-1. Diameter of workpiece
12-2. Guide plate
12-3. Spacer block
12-4. Width of spacer block
12-5. Vise
13-1. Blocks
14-1. Under cover
14-2. Wing bolt
16-1. Limit mark
17-1. Screwdriver
17-2. Brush holder cap
2414NB
355 mm
25.4 mm
3,800
500 mm x 280 mm x 620 mm
18.4 kg
/II
) : 99 dB(A)
pA
) : 109 dB(A)
WA
Wear ear protection
) : 4.0 m/s
h
2
ENG905-1
ENG900-1
2
ENG901-1