Facom DL.15AL Original Bedienungsanleitung Seite 6

EXTREMELY IMPORTANT:
Read these safety instructions carefully in addition to the instructions for use, operation and maintenance. Keep this instructions sheet in an easy place to find
as you may need to use it again.
This hydraulic trolley jack has been designed for use in the elevation of cars and lorries.
Any other application, beyond the conditions established for use of this hydraulic trolley jack will be considered inappropriate.
Handle the hydraulic trolley jack correctly and ensure that all parts are in good condition prior to its use.
Do not modify the hydraulic trolley jack in any way.
The manufacturer accepts no responsibility for the improper use of the hydraulic trolley jack.
1 SAFETY INSTRUCTIONS (§ 7.1.1 de l'EN 1494+A1)
The owner and/or operator shall have an understanding of the product, its operating characteristics, and safety operating instructions before operating it.
Safety information shall be understood:
1.1 Study, understand and follow all instructions before operating this device.
1.2 Do not exceed rated capacity.
1.3 Support the vehicle with appropriate means immediately after lifting.
1.4 Lift only on areas of the vehicle as specified by the vehicle manufacturer.
1.5 No alterations shall be made to this product.
1.6 Only attachments and/or adapters applied by the manufacturer shall be used.
1.7 Visual inspection shall be made before each use by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing
parts.
1.8 It shall be the responsibility of the employer to ensure that applicable personal protective equipment (PPE) complies with applicable local safety codes.
1.9 Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE UNTIL
REPAIRED OR REPLACED.
1.10 The hydraulic trolley jack should be supported on a solid, level and horizontal surface which is well illuminated and free of obstructions. Never stand the
hydraulic trolley jack on a surface which may sink.
1.11 Ensure that there are no persons inside the vehicle to be lifted. Switch off the engine and apply the brake. Ensure the vehicle or element to be lifted
against any type of sliding. Use chocks if appropriate (1). Do not enter the vehicle or start the engine while it is supported on the jack or appropriate
stands. The hydraulic trolley jack is a lifting device only and should never be used to move the vehicle.
1.12 During raising and lowering of the load, all precautions should be taken to avoid movement of the vehicle load. Traffic may cause the raised vehicle to
rock during roadside use of the hydraulic trolley jack.
1.13 The hydraulic trolley jack should be positioned so as to avoid the need for the user to introduce any part of his/her body underneath the vehicle. Never
work under a raised vehicle without previously supporting it with mechanical stands (3) or other appropriate methods. Never position any part of your
body near the movable elements of the hydraulic trolley jack.
1.14 It is necessary for the operator to be able to observe the lifting device and the load during all movements. In the presence of dangerous conditions, such
as movement of the vehicle, etc, the lifting process must be interrupted.
1.15 Ensure that there are no persons or obstructions underneath the vehicle prior to lowering.
1.16 As an additional safety measure against overload, the hydraulic trolley jack is fitted with an overload valve set at the factory and which should not be
adjusted under any circumstances.If nominal capacity of the jack is exceeded the overload valve will stop the lifting operation.
1.17 If the device jams, lift the vehicle with another jack until the first can be cleared.
1.18 Do not use the aluminium hydraulic trolley jack in the presence of violent wind, frost, under extreme climates, near powerful magnetic fields or potentially
explosive atmospheres.
1.19 Avoid any contact between the aluminium hydraulic trolley jack and food.
1.20 Never use this aluminium hydraulic trolley jack to lift persons
1.21 Never use this aluminium hydraulic trolley jack as a handling means (for moving loads)
1.22 Before use on a ship, please refer to the safety instructions in point 1.10 of these instructions
1.23 The maximum manual forces required for operating the aluminium hydraulic trolley jack (unloaded and loaded with the nominal load respectively) do not
exceed the following values:
To start moving an unloaded movable or mobile aluminium hydraulic trolley jack : 300 N
To maintain the movement of the unloaded aluminium hydraulic trolley jack : 200 N
To start moving a loaded mobile aluminium hydraulic trolley jack : 400 N
To maintain the movement of the loaded aluminium hydraulic trolley jack : 300 N
To lift the loaded aluminium hydraulic trolley jack using the lever of a hand pump: 400 N
To lift the loaded aluminium hydraulic trolley jack using a foot pump: 400 N
To lift the aluminium hydraulic trolley jack with a rated load ≤ 5 t using a crank: 250 N
NOTE If the loads generated exceed these values, they must be reduced by the intervention of additional persons.
1.24 If oil overflows, please do not use the aluminium hydraulic trolley jack, and refer to section 5 of these user instructions or contact your Facom dealer.
1.25 This aluminium hydraulic trolley jack is designed for 5000 operating cycles minimum.
1.26 This aluminium hydraulic trolley jack complies with the NF EN 1494+A1 standard: Mobile or movable jacks and associated lifting equipment.
Failure to heed these markings may result in personal injury and/or property damage.
2. USE AND OPERATION (§ 7.1.2 de l'EN 1494+A1)
Important: Prior to lifting the load, ensure that all of the mentioned safety instructions are followed.
Lifting
2.1 Place the vehicle in park with emergency brake on and wheels securely locked to prevent inadvertent vehicle movement.
2.2 Locate and close release valve by turning clockwise until firm resistance is felt to further thread engagement. Center hydraulic trolley jack saddle under
lift point.
2.3 Verify lift point, insert handle into handle sleeve and pump to contact lift point. To lift, pump handle until load reaches desired height.
2.4 Transfer the load immediately to a pair of appropriately rated jack stands.
USE ONLY THE HANDLE ASSEMBLY PROVIDED BY THE JACK MANUFACTURER.
Lowering
2.5 Raise load high enough to clear the jack stands; then carefully remove jack stands.
2.6 Slowly turn the handle counterclockwise, but no more than a 1/2 turn. If the load fails to lower :
. Use another jack to raise the vehicle high enough to reinstall jack stands,
. Remove the affected hydraulic trolley jack and then the stands,
. Using the other jack, lower the load by turning the operating handle counterclockwise, but no more than a 1/2 turn.
- After removing jack from under the load, push saddle down to reduce ram exposure to rust and contamination.
6
NU-DL.15AL-DL.25AL_0117 à traduire.indd 6
EN
31/01/2017 16:05:19