Salda Stouch Bedienungsanleitung Seite 41

EN
Elements Elements
B1 B1
L1 L1
B1 B1
L1 L1
L1 L1
Activation from sleep Activation from sleep
B2 B4 B6 B2 B4 B6
L2 L2
B3 B4 B6 B3 B4 B6
Set temperature Touch B3. Set temperature Touch B3.
L3 L3
B4 B6 B4 B6
Change value of se- Change value of se-
L4-L7 L4-L7
B4 B5 B6 B4 B5 B6
L2 L2
Switch on/off the inten- Switch on/off the inten-
sive ventilation (boost) 2 sekundes palaikyti B5.
sive ventilation (boost)
B4 B6 B4 B6
L4-L7 L4-L7
Review and cancel Review and cancel
L2-L7 L2-L7
B2 B3 B5 B2 B3 B5
"Child safety feature" "Child safety feature"
Connection indication
Flashing „Con" – connecting.
Shining „noC" – connection lost or there is no connection with the controller.
NOTE: This paragraph applies when the controller is used as a Modbus master.
Fan speed control options
• Selecting 4 preset speeds;
• Selecting percentage value of speed (0,20 - 100 %) only for 0...10 VDC output and ECO controller;
• User menu speeds are set in intervals of 5 %;
• Service menu speeds are set in intervals of 1 %;
• According to a preset 4 pressure values.
NOTE: only van directly connected to remote controller is controlled according to a pressure. Pressure transmitter
also has to be connected to the remote controller.
• Maximum ventilation. The unit operates in maximum speed (according to boost configuration). Maximum speed
is limited by timer which can be easily set (see table);
• Maximum speed can be activated using fast button. When preset maximum fan speed (boost) time is over,
previous speed is automatically restored;
• 0..10 VDC CO sensor can be connected for activation of maximum speed based on the given CO
2
www.salda.lt
Coomand Action Coomand Action
Press down for 2 seconds Press down for 2 seconds
Switch on Switch on
B1 B1
Press down for 2 seconds Press down for 2 seconds
Switch off Switch off
B1 B1
Press any button. Press any button.
mode mode
Set fan speed Touch B2. Set fan speed Touch B2.
Increase by touching B4, Increase by touching B4,
lected setting lected setting decrease by touching B6 decrease by touching B6
Press down for 2 seconds
B5.
For canceling, press down For canceling, press down
alarms alarms B2 and B3 for 3 seconds. B2 and B3 for 3 seconds.
CO2 blow off CO blow off
2
On/off On/off Press down B3, B2 and Press down B3, B2 and
B5 for 2 seconds. B5 for 2 seconds.
Indication Indication
L1 lights on. L1 lights on.
L1 lights off. L1 lights off.
L1 flashes slowly in sleep mode. L1 flashes slowly in sleep mode.
L2 lights on. Speed is adjusted by touch-
ing elements B4 and B6
L3 lights on. Temperature is adjusted by L3 lights on. Temperature is adjusted by
touching elements B4 and B6 touching elements B4 and B6
Numbers change in the segment display.
L4, L5, L6, L7 shows selected fan speed.
L2 flashes. Remaining time in seconds is L2 flashes. Remaining time in seconds is
shown in the segment display (for values shown in the segment display (for values
above 600s, time is shown in minutes). above 600s, time is shown in minutes).
Time is adjusted (during operation of the Time is adjusted (during operation of the
function) by touching B4 and B6. function) by touching B4 and B6.
Maximum BOOST running time: 180m. Maximum BOOST running time: 180m.
(3h) (3h)
In case of alarms, L4, L5, L6, L7 flash In case of alarms, L4, L5, L6, L7 flash
and alarm code is shown in the segment and alarm code is shown in the segment
display (A.01, A.02 etc.). You can review display (A.01, A.02 etc.). You can review
alarm list by using elements B4 and B6. alarm list by using elements B4 and B6.
After alarm is canceled, controller returns After alarm is canceled, controller returns
to initial state. NOTE: It is strongly prohib- to initial state. NOTE: It is strongly prohib-
ited to cancel the alarm without removal ited to cancel the alarm without removal
of its cause. This must be performed by of its cause. This must be performed by
service representatives or staff. service representatives or staff.
L2, L3 and L7 flash, L4, L5, L6 light on. L2, L3 and L7 flash, L4, L5, L6 light on.
Non active elements B1, B4 and B6. After Non active elements B1, B4 and B6. After
pressing unavailable button, segment pressing unavailable button, segment
display shows "−−−" display shows "−−−"
parameters.
2
41