Operation; Maintenance - Husqvarna SL546E Originalanleitung

OPERATION

CONNECTION v220/230 - 50 Hz
ATTENTION MOTOR PROTECTOR
A motor cut -out device (motor protector) has been
incorporated in the switch. Therefore, when reaching
excessive cutting stress or overload, the motor will cut
out automatically.
For re-starting, wait until the motor will be cool (approx. 5
to 10 minutes);
VERSION Manual lawn mower
Before connecting up the lawn mower to the electric
power supply, make sure that the mains supply voltage is
220-230V/50Hz and that a ground fault interrupter is
installed on the mains circuit. Start the mower as follows:
a) Press the safety push-button (5) to enable mower
startup.
b)Start the mower by pulling the lever (11) towards the
handle and keeping it pressed down. If you release the
lever, the motor will stop.
CAUTION! The blade starts turning as soon as the
mower is started.
MOWING
To cut the grass, push the lawn mower manually
ADJUSTMENT OF CLUTCH CABLE
Important: If, when you press the clutch lever, the automatic advance gear does not engage, the clutch
cableshould be adjusted by inserting the spring (P) in one of the subsequent holes (S) in the clutch lever (13).
AUTOMATIC ADVANCEMENT
Periodically check the automatic advance assembly and
make sure to keep it clean. In particular,the pinion (15)
and the gear (16) must be kept perfectly clean. To carry

MAINTENANCE

• Frequently check the mower and ensure that all grass
deposits are removed from beneath the deck.
• Never clean the mower by pouring water over it: this
may seriously damage the electrical system.
• Frequently remove the wheel screws clean with
BLADE
• To remove the blade (19) unscrew the screw (20).
• Check the conditions of the blade-support (21), the key
(22) and replace any parts which are damaged.
• When reassembling, make sure that the key (22) is
ENVIRONMENTAL INFORMATION
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
VERSION Self-Propelled
Before connecting up the lawn mower to the electric
power supply, make sure that the mains supply voltage is
220-230V/50Hz and that a ground fault interrupter is
installed on the mains circuit. Start the mower as follows:
a) Press the safety push-button (5) to enable mower
startup.
b) Start the mower by pulling the lever (11) towards the
handle and keeping it pressed down. If you release
the lever, the motor will stop.
CAUTION! The blade starts turning as soon as
the mower is started.
MOWING
To cut the grass, push the lawn mower manually or insert
the automatic advance gear.
How to insert automatic advance: Lift up the clutch lever
(13) and keep it pressed in position.
How to disengage advance: Release the clutch lever.
(for self-propelled versions only)
(for self-propelled versions only)
out this check, you must remove the wheel (17) by
unscrewing the screw (18). Before reinstalling the wheel,
put grease on the pinion and gear.
Before carrying out any operations on the
cutting tool, remove plug from mains
petroleum and oil before replacing. Ball bearings must
be greased before remounting.
• Frequently check the blade for damage.
• The lawn mower must be checked by a SERVICE
DEALER.
correctly seated in the shaft and that the cutting edges
face in the direction of the engine rotation. The blade
screw (20) must be torqued to 3,7 Kgm (35 Nm).
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product,
please contact your local council office, your household
waste disposal service or the shop where you purchased
the product.
ENGLISH - 3