Symbols Used In The Manual - Crown CT15212 Original Bedienungsanleitung

Seite von 156

/ 156
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

• Note that when you operate a power tool, please

hold the auxiliary handle correctly, which is helpful

when controlling the power tool� Therefore, proper

holding can reduce the risk of accidents or injuries�

Service

• Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained�

• Follow instruction for lubricating and changing ac-

cessories�

Special safety warnings

Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electric shock�

Safety guidelines during power tool

operation

• Fix the workpiece. Use a fixing device or a vice to fix

the work piece for safely and steadily�

• Take necessary and proper safety measures when

harmful, flammable or explosive dust is produced in

the work� For example, dust that may cause cancer is

produced during the operation� Please use dust and

chip collecting device and wear a dust mask in the work�

• Keep workplace tide and clean� The mixed materials

would be extremely dangerous� Light metal dust would

be combusted and explode easily�

• Do not process materials that contain asbestos�

Asbestos is cancerogenic substance�

• Put down the power tool when the saw blade is fully

stopped�

• Do not use power tool when cable is damaged� If

the power wire is damaged or broken in the work, do

not touch it and pull out the plug immediately� Using

broken wire would lead to electric shock easily�

• Keep hands away from sawing area� Hand shall not

hold the lower part of work piece� Your hand would be

cut when it touches saw blade�

• First start the power tool and then put the power tool

of the workpiece to process it� If the saw blade is stuck

in the workpiece and power tool would rebound�

• Attention: the base plate shall cling to the workpiece

during the sawing. If the saw blade is deflected, it

would be broken and power tool would rebound�

• Cut off the power of power tool when work is done

and take the saw blade when the power tool is fully

stopped� The power tool wouldn't rebound in this way

and it can be put down safely�

• Use undamaged and crackles saw blade only�

Bended or dull saw blade would be broken easily and

cause rebound of power tool�

• After the power tool is shut down, do not stop the

moving saw blade by side pressure� The blade saw

would be damaged or broken and further lead to

rebound in this way�

• Use proper detector to detect whether there is

concealed circuit and pipeline in the operation area

and ask the local construction organization for

assistance if necessary� In the work, if the cable is

cut off, it would cause fire disaster and electric shock.

Damaged gas pipe would explode� If the water pipe

is cut off, it would cause property losses and electric

shock to the operator�

• Fix the saw blade rigidly with the saw holder� Check

the fixing of the saw blade regularly.

• Before cutting of wood, remove any metal objects

from the material (nails, screw nails, straps, etc�)�

• Avoid stopping an power tool motor when loaded�

• During operation watch the position of a power cable

(it should always be positioned behind the power tool)�

Do not allow it to whip around your legs or arms�

• Should power supply fail during work, immediately

turn the power tool's switch "Off" in order to avoid

accidental turning of the power tool on�

• After the power tool is switched off, the saw blade

keeps moving mechanically for some time, therefore

put the power tool aside only after the saw blade is

completely immobile�

• The saw blade gets quite hot during the operation,

therefore do not touch the saw blade until it is

completely cooled off�

Warning:

contained in dust generated in sanding,

cutting, sawing, grinding, drilling and

other construction industry activities may

result in cancer, congenital deficiency or be

harmful to the fertility. The ion of some chemical

substances shall be:

• before any repair and replacement work to

the machine, the power plug must be pulled out

firstly;

• the transparent two silicon oxide and other

masonry products in the wall bricks and cement;

the chromium arsenic (CCA) in wood with chemical

treatment� The harm degree of these substances

shall depend on the frequent degree of you carrying

out these works� If you want to reduce the contact

with these chemical substances, please work in

the place with ventilation and you shall use the

appliances with safety certificates (such as the dust

mask designed with tiny dust filter).