Practical Advice - Bosch AdvancedMulti 18 Originalbetriebsanleitung

using the on/off switch (2).
Charge the battery or let it cool down before switching the
power tool on again. Failure to do so can damage the bat-
tery.
The 180° light band (11) improves visibility in the immedi-
ate work area. It is automatically switched on and off with
the power tool.
Do not look directly into the worklight; it can blind
u
you.
Preselecting the orbital stroke rate
You can even preselect the required orbital stroke rate dur-
ing operation using the orbital stroke rate preselection
thumbwheel (6).
The required orbital stroke rate is dependent on the material
and the work conditions and can be determined using prac-
tical tests.
Orbital stroke rate level "6" is recommended for sawing, cut-
ting and sanding harder materials, such as wood or metal;
orbital stroke rate level "4" is recommended for softer ma-
terials, such as plastic.

Practical Advice

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Note: Do not keep the ventilation slots (7) on the power tool
closed when working as this will reduce the service life of the
power tool.
Operating principle
The oscillating drive causes the application tool to oscillate
back and forth by 2.8° up to 20000 times per minute. This
enables precise work in the tightest of spaces.
Use a consistent, low contact pressure
when performing work; otherwise, the
performance will be impaired and the ap-
plication tool may jam.
While working, move the power tool back
and forth to prevent the application tool
overheating and jamming.
Sawing
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
When sawing lightweight materials, take into account
u
the statutory provisions and recommendations of the
material manufacturers.
Bosch Power Tools
Plunge cuts may only be applied to soft materials,
u
such as wood, gypsum board, etc.
Before using HCS saw blades to saw into wood, chipboard,
building materials, etc., check these saw blades for foreign
objects, such as nails, screws, etc. Remove the foreign ob-
jects as required or use bi-metal saw blades.
Cutting
Note: When cutting wall tiles, please bear in mind that the
application tools are subject to high wear if used for exten-
ded periods.
Sanding
The material removal rate and sanding result are primarily
determined by the choice of sanding sheet, the preselected
orbital stroke rate level and the contact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
To sand corners, edges and hard-to-reach areas accurately,
you can also work with the tips alone or with an edge of the
sanding plate.
The sanding sheet may heat up significantly when used to
sand specific points rather than entire surfaces. Reduce the
orbital stroke rate and contact pressure and allow the sand-
ing sheet to cool down at regular intervals.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch sanding accessories.
Always connect a dust extraction system for sanding.
Scraping
Select a high orbital stroke rate level for scraping.
Work on a soft surface (e.g. wood) at a flat angle and with
low contact pressure. Failure to do so may cause the scraper
to cut into the surface underneath.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. In the event of excessive load or temperatures out-
side of the permitted battery temperature range, the power
tool switches off. Switch the power tool off, allow the battery
to cool down, then switch the power tool back on.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
English | 23
1 609 92A 4N1 | (12.10.2018)