Bosch AdvancedMulti 18 Originalbetriebsanleitung Seite 21

Application tool
TC-Riff sanding fin-
ger
TC-Riff plunge cut
saw blade
HCS universal joint
cutter
Fitting/changing the application tool (AutoClic)
(see figures A–B)
Remove the application tool if one has already been fitted.
To do so, open the AutoClic lever (1) all the way. The applic-
ation tool/accessory will be ejected.
Place the required application tool (e.g. plunge cut saw
blade (12)) on a level surface so that the depressed centre
is face down (see figure on the graphics page; you should be
able to read the text on the application tool from above).
Turn the application tool to a position which is convenient
for the job at hand. Press the power tool onto the application
tool at the required angle until it audibly engages.
Check that the application tool is seated securely. Ap-
u
plication tools that are attached incorrectly or are not se-
curely fixed in place may come loose during operation,
thereby putting you at risk.
Fitting and Adjusting the Depth Stop
The depth stop (15) can be used when working with seg-
ment saw blades.
Remove the application tool if one has already been fitted.
Slide the depth stop (15) over the tool holder (10) and onto
the collar of the power tool as far as it will go, with the la-
belled side facing upwards.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: Cutting depths 8 mm, 10 mm, 12 mm and
Choosing the Sanding Sheet
Different sanding sheets are available, depending on the material you are working with and the required surface removal rate:
Sanding sheet Material
– All wood and wood-
based materials (e.g.
hardwood, softwood,
chipboard, construction
Red quality
boards)
– Metal materials
Bosch Power Tools
Material
Wood, paint
Fibreglass, mortar, wood Plunge cuts in extremely abrasive materials;
Expansion joints, window
putty, insulation materials
(rock wool)
– With segment saw blades ACZ 100 .. with a diameter of
Insert the appropriate segment saw blade for the desired
cutting depth. Slide the depth stop (15) from the tool holder
(10) in the direction of the application tool until you can ro-
tate it freely. Rotate the depth stop (15) so that the desired
cutting depth is above the section of the saw blade that will
be used to saw. Slide the depth stop (15) onto the collar of
the power tool once again as far as it will go.
Remove the depth stop (15) for all other cutting depths and
for working with other application tools. To do this, remove
the application tool and pull the depth stop away from the
collar.
Fitting the Auxiliary Handle (accessory)
The low-vibration auxiliary handle enables the tool to be
used safely and more comfortably.
Screw the auxiliary handle into the thread (9) on the left or
right of the machine head depending on how you are work-
ing.
u
Application
For pre-sanding, e.g. of rough and uneven beams and
boards
For surface sanding and levelling of slight irregularities Medium
For finish-sanding and fine sanding of wood
Application
Sanding of wood or paint in hard-to-reach areas without
sanding paper;
example: Sanding off paint between window shutter slats,
sanding wooden flooring in corners
example: Routing of thin mosaic tiles
Cutting soft materials;
example: Cutting silicone expansion joints or window
putty
14 mm (information on the depth stop in a larger font size
and without brackets).
100 mm: Cutting depths 14 mm, 16 mm, 18 mm and
20 mm (information on the depth stop in a smaller font
size and in brackets).
Do not continue to use the power tool if the auxiliary
handle is damaged. Do not make any alterations to the
auxiliary handle.
English | 21
Grit
Coarse 40
60
80
100
120
Fine 180
240
320
400
1 609 92A 4N1 | (12.10.2018)