Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note: If the battery pack feels very warm, the
pack will cool more quickly in your "AIR
COOLED" charger.
Note: The machine will cool more quickly if you
operate it at idling speed.
3. If the current is too high (for example, if the
machine seizes continuously for long periods),
the machine switches off.
Switch off the machine at the trigger switch (6).
Then continue working as normal. Try to prevent
the machine from seizing.
ENG
9. Accessories
Only use original Metabo battery packs and Metabo
accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
A Battery chargers: ASC Ultra, ASC 15, ASC 30
and others.
B Battery packs 18 Volt: 5.2 Ah (6.25592); 4.0 Ah
(6.25591); 3.0 Ah (6.25594), etc.
See www.metabo.com or the catalogue for a
complete range of accessories.
10. Repairs
Repairs to electrical tools must ONLY be carried out
by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2012/19/EU
on waste electrical and electronic equipment and its
implementation in national legal systems.
Special notes regarding cordless machines:
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).
12. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U
= Voltage of battery pack
P
= Rated input
1
n
*
= No-load speed
1
n
*
= On-load speed
2
ø max = Maximum drill diameter
s max = Maximum impact rate
b
= Chuck capacity
G
= Drill spindle thread
H
= Drill spindle with hexagon socket
m
= Weight with smallest battery pack/weight
without cord
D
= Collar diameter
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
AC Power
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
* Energy-rich, high-frequency interference can
cause fluctuations in speed. The fluctuations
disappear, however, as soon as the interference
fades away.
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
= Vibration emission value
h, D
(Drilling in metal)
K
= Uncertainty (vibration)
h,D
Typical A-effective perceived sound levels:
L
= Sound-pressure level
pA
L
= Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
Wear ear protectors!
ENGLISH en
13
Werbung
Inhaltsverzeichnis
