Maintenance - Cresto 1128 Gebrauchsanweisung

Figure A Parts of the harness
1. D ring on the back, or where relevant two textile loops on the chest, for attaching to protective equipment against falls;
EN355, EN 353-1/-2, EN360. Attachment points for these products are labelled "A" on the harness.
2. Textile loops
3. Buckle for shoulder adjustment
4.Buckle for leg support adjustment
5. Chest strap with plastic buckle
6. D-Rings for support and positioning according to EN-358 and EN-813. According to CNB/P11.043, Rev 2.
Figure B
1. Closing the clasp
2. Locked position
3. Opening the clasp
Figure C Putting on the harness
1. Grip the D-ring on the back of the harness to untangle the harness's straps.
If the leg, chest or belt buckles are closed, open these.
2. Hold the harness's shoulder straps and put on the harness like a jacket.
3. Close the chest strap buckle.
4. Take hold of the leg straps between the legs and close using the appropriate buckles.
Adjust the leg straps so that they fit tight around the legs. (It shall be possible to insert fingers but not the hand).
5. If the harness is equipped with adjustable shoulder straps, adjust these so the
harness fits snugly against the body, not too tight.
6. Adjust the chest strap so that it holds the shoulder straps in a fixed position.
Figure D
Fixing points on harness that may be used for protection against falling (EN-361) are D ring on back or two textile loops on the chest.
Fall arrest harness EN-361, EN-358
USER INSTRUCTIONS
NOTE! Read and understand all the user instructions before using the equipment!
The harness is tested and certified according to the EN standard EN-361 (protection
against falling) and where relevant EN-358 (support belt). The harness is manu-
factured of 45 mm wide polyester webbing, metal clasps and some models have a
quick-action catch of polyamide to hold the chest straps together. The harness may
be attached to (read EN-363:2008): Safety lanyards, Shock absorber lanyards, Fall
arrestors or Sliding locks/Runners for permanent installations. These fixing points
are marked with a label "A" and may be used on system for protection against
falling. These points are D ring on back or chest and, in relevant cases, the two belt
eyelets (buckles) on the chest together. A full body harness (EN361) is the only type
of harness that can hold the body in an upright position when used in a system for
protection against falling.
If the harness is equipped with the two D rings on the side may only be used for
support line and positioning. Attachment to belt only is not regarded as protection
against falling.
Warning! Work at high heights requires the user to be in good health (see EN-
365), to be trained in the use of the equipment and to be aware of the risks. Planning
for the evacuation of persons that have fallen and that may remain hanging from
the harness must be done before starting work at high heights. If you are uncertain,
contact the dealer or the manufacturer for more information.
Warning! Before using the product for the first time it should be suitably adapted.
The adaptation is to be made in a safe place to ensure the correct size, that there
is adequate possibility for adjustment and that an acceptable level of comfort is
achieved for the intended work.
Warning! The harness must not be modified or supplemented using accessories
other than those supplied by the manufacturer. Repairs or replacement of parts may
only be carried out by the manufacturer.
Warning! The harness is only designed for personal protection, all other usage is
forbidden. If possible, the user should have his own personal harness (see EN-365).
It is important that the user makes an ocular inspection of the equipment before use.
Warning! When connecting the system in accordance with EN-363, the user shall
be fully conversant with the function and use of other components. In the event of
uncertainty contact your dealer or the manufacturer.
Before each use: Carefully make an ocular inspection of the material and func-
tion and ensure that the equipment works. Pay attention to the possibility of webbing
breakage, damaged seams, cuts, discoloration, damaged D-rings and clasps, the
function of adjuster and buckles.
Warning! The product must be replaced immediately if faults are discovered on the
equipment that are considered to reduce safety. In the event of uncertainty contact
the dealer or the manufacturer for an inspection.
Warning! The product must be discarded and replaced immediately if a fall has
occurred when using the equipment.
Warning! With the connection of the fall protection system, the anchor point must
be approved according to EN-795 or the equivalent to withstand a load of 12 kN.
The anchor point should, where possible, be directly above the user. Work is to be
carried out in such a manner that the fall distance and the risk of falling are kept to a
minimum. Avoid sideways movements that cause swinging where you can be thrown
against an object or a wall!
Warning! Lowest ultimate load on the equipment is 15 kN.
Warning! Observe the need of sufficient space beneath the workplace, in some
cases at least 6 m, below the person subjected to possible fall with the shock absor-
ber. Observe length of the shock absorber in extended mode, height of the worker,
position of the anchor point and length of the shock absorber line.
Warning! When working with the harness the greatest caution must be observed
when suspended in the system. Should the user become unconscious in a suspen-
ded mode it will be extremely urgent to relieve the person of mechanical tension
(knowledge of how to take down a person in an emergency is therefore essential).
The situation, referred to as "suspension trauma", could be fatal. Make sure that
you never work alone. Make sure that you are alert, are sufficiently in motion while
working, have consumed sufficient fluids, and are suitably dressed for the prevailing
conditions.
NB Make a habit of regularly checking the buckles and their correct adjustment while
in use (EN 358).
NOTE! The fall protection's material or its function may be affected if subjected to:
extremely high temperatures, chemicals, electrical current, grinding, cutting, wear
against sharp objects and the affects of the weather.
NOTE! The equipment must be stored in a dry, dark and well-ventilated space.
Lanyards are to be hung in gentle bights. Appropriate bags and/or transport boxes
are to be used when transporting the equipment.
NOTE! All Cresto fall protection equipment has labels for marking. The label shows
the manufacturer's name, product name, model type, unique serial number, date of
manufacture, EN norm and Certification Institute number.
NOTE! The product's maximum lifecycle is 10 years from the date of first use (max
2 years' addition from the first production date). Incorrect handling and wear-and-tear
can significantly shorten the lifecycle. The product shall be discarded if it has:
corrosion damage, several thread breakages, cut-off tape edges by more than 2 mm,
discoloured tapes, heavy wear-and-tear "colour worn away", corroded metal parts or
if it lacks functionality and marking (ask Cresto if unsure).
Warning! If the product is exported, the retailer shall provide a translation of this
user's instruction, maintenance and inspection instruction to the language where the
product is to be used.

MAINTENANCE

NOTE! The equipment shall be stored in a dry, dark and well-ventilated location,
protected against steam, sharp edges, vibration and UV-light. The equipment shall
be kept clean for best functionality and durability. Metal parts can be blown clean with
compressed air. Avoid lubricating oil! Lightly soiled equipment can be washed with a
brush in lukewarm water. A mild soap solution can be used. Heavily soiled equipment
can be machine-washed in a wash-bag with phosphate-free detergent in a 40°
programme. Wet equipment is hung up to dry. Equipment shall be allowed to air-dry
without being subjected to open fire or any other heat source.
INSPECTION
Warning! For the user's safety the product shall be inspected at least every twelfth
month in order to ensure its functionality and durability (refer to EN 365). The
inspection can be registered in Inspector online at www.cresto.se
NOTE! In cases of frequent usage of the equipment or in aggressive environments,
inspections shall be carried out at shorter intervals (as decided by a trained
competent person).
Warning! The inspection shall be carried out by a competent person (a person who
has been trained and is competent in fall protection equipment inspection) who holds
a certificate for inspection and in accordance with the manufacturer's inspection
procedure as well as EN 365.
NOTE! The product's label marking shall be legible! (The harness is also fitted with
a RFID/NFC chip for traceability if the label is not legible)
LOG
Each component in a fall protection system (EN363:2008) shall be entered in a log.
The log is completed by a "competent person" at least every twelfth month. (Refer
to Inspector at www.cresto.se). Documentation is available for download from www.
cresto.se
REPAIRS
Repairs to the products may only be carried out by the manufacturer.
EU type inspection carried out by:
SP - Sveriges Tekniska Forskningsinstitut.
Box 857. SE-501 15 BORÅS. Sweden. www.sp.se
Notified Body no. 0402
ENG