Metabo SE 2500 Originalbetriebsanleitung Seite 10

en ENGLISH
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
LED lights (6): Do not observe the LED radiation
directly with optical instruments.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Belt hook (mains powered tools) *
2 Rotation selector switch
3 Trigger switch
4 Lock button (continuous operation)
5 Handle
6 LED lights
7 Battery pack release button
8 Belt hook (cordless tools)*
9 Battery pack *
10 Capacity and signal indicator *
10
11 Capacity indicator button *
12 Depth stop
13 screwdriver bit*
14 Bit holder
15 Screwdriver spindle
16 Closure sleeve
17 Stop sleeve
* depending on the model / features
a 6. Commissioning
6.1 For mains powered machines only
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
6.2 For cordless machines only
Battery pack
Charge the battery pack (9) before use.
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
Li-Ion battery packs "Li-Power" have a capacity and
signal indicator (10):
- Press the button (11), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the battery pack
Removal: Press the battery pack release button (7)
and pull the battery pack (9) forwards.
To insert: Slide the battery pack (9) in until it
engages.
Installation of belt hook
The belt hook (8) may be screwed into place on the
left or the right (see illustration, page 2).
7. Use
7.1 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Do not activate rotation selector switch (2)
unless the motor has completely stopped.
See page 2:
R = Clockwise setting
L = Counter-clockwise setting
0 = Central position: transportation lock setting
(switch-on lock)
7.2 On/Off switch, modifying the speed
Switching on, speed: press the trigger switch (3).
Press in the trigger to increase the rotational
speed.
To switch off release the trigger switch.