Operation; Connecting The Rechargeable Battery Belt System (02) To (05); Inserting The Rechargeable Battery (06); Establishing The Voltage Supply (07, 08) - AL-KO solo HT 4260 Betriebsanleitung

Operation

NOTE
When charging, the rechargeable bat-
tery is protected from overcharging due
to automatic detection of the charge sta-
tus and thus can remain connected to
the charging unit for some time, but not
permanently.
1. Connect the rechargeable battery (01/6) and
charging unit (01/7), as well as the charging
unit to the mains voltage. The charging pro-
cess begins. The LED on the charging unit
lights green, the charge status is displayed
on the rechargeable battery.
2. Observe the charge status displays on the re-
chargeable battery. The charging process
takes approx. 2.5 hours until fully charged.
The charging process ends automatically
when the rechargeable battery is fully
charged.
3. Disconnect the rechargeable battery from the
charging unit and the charging unit from the
mains voltage.
8 OPERATION
WARNING!
Risk of injury due to detaching appli-
ance parts
Appliance parts detaching during opera-
tion can lead to serious injury.
■
Before turning the appliance on,
check that all the parts of the appli-
ance are firmly tightened.
■
Attach cutting tools so that they can-
not detach during operation.
8.1 Connecting the rechargeable battery
belt system (02) to (05)
Connect the rechargeable battery belt system ac-
cording to the illustration (02) to (05).
8.2

Inserting the rechargeable battery (06)

Inserting the battery
1. Push in (06/a) the rechargeable battery
(06/1) into the rechargeable battery belt sys-
tem (06/2) until it locks.
Pull out the rechargeable battery
1. Press and hold the unlock button (06/3) on
the rechargeable battery (06/1).
2. Pull out (06/b) rechargeable battery (06/1).
442203_a
8.3

Establishing the voltage supply (07, 08)

Mounting the connecting cable
1. Align the first connector of the connecting ca-
bles (07/1) to the guiding pin and guide slot
of the rechargeable battery belt system con-
nector (07/2), join, and turn slightly clockwise
until the locking and unlocking switch (07/3)
audibly engages.
2. Align the second connector of the connecting
cables (08/1) to the guiding pin and guide slot
of the connection socket, push (08/a) into the
connection socket of the appliance (08/2),
and turn slightly clockwise until the locking
and unlocking switch (08/3) audibly engages.
Dismounting the connecting cable
1. Pull the locking and unlocking switch (07/3)
backwards (07/b), turn the connector slightly
to the left and pull out (07/c).
2. Pull the locking and unlocking switch (08/3)
backwards (08/b), turn the connector slightly
to the left and pull out (08/c) of the connec-
tion socket of the appliance (08/2).
8.4

Turning the rear handle (11)

Turning the handle
1. Press the unlock button (11/1).
2. Turn the handle to the left or right by 90 ° (11/
a) until it engages.
3. Release the unlock button (11/1).
Turning the handle back
1. Press the unlock button (11/1).
2. Turn the handle back to the initial position un-
til it engages.
3. Release the unlock button (11/1).
8.5

Starting the hedge trimmer (09)

1. Stand securely.
2. Hold the front handle (09/1) with one hand
and the rear handle (09/2) with the other
hand.
3. Press the safety switch on the front handle
(09/a), then press the on/ off switch on the
rear handle (09/b). The appliance starts.
4. Keep both buttons pressed while working.
When a button is released, the appliance
switches off.
31