HQ Power VDPL300BA Bedienungsanleitung Seite 4

• Only use t he device fo
lamp explo osion, crash,
• Damage ca aused by dis
dealer will not accept r
• Mechanica l wear and L
• A qualified technician s
• Do not swi itch the devi
device aga ainst damage
• This device e is designed
be used in doors with a
• Lighting ef ffects are no
• There may y be some sm
normal and d any smoke
• Use the or iginal packa
• Keep this m manual for f
4. . Over rview
Re fer to the ill ustrations o
1 1 fuse
2 2 power in put
3 3 DMX outp put
4 4 remote c control input
5. . Moun nting Ins
Ch hoosing a M Mounting Lo
The V VDPL300BA
opera ation, the un
Do o not:
• Operate th he device in
higher tha n 75%.
• Operate th he device in
Se ecure Moun ting
Risk k of injury. O
deter rmining the
regu larly. Do not
insta allation may
• Have the d device instal
• The carryin ng construct
deforming .
• The installa ation must a
• Never stan nd directly be
technician check the d
• Install the device in a
• Make sure there is no
• The installa ation has to
DM MX-512 con nnection
Re fer to the ill ustrations o
• When appl icable, conn
other side to the male
serial linkin ng. The linki
• A DMX term minator is re
an electric ally noisy en
signal by e electrical noi
and 3, whi ch is then p
V. 02 – 25/09/2 012
r its intende ed purpose. A
, etc. Using t the device in
sregard of ce ertain guidel
responsibility y for any en
LEDs are not t covered by
should insta ll and servic ce this device
ce on imme diately after
e by leaving it switched
d for profess sional use on
an alternatin g current of
ot designed f for permanen
moke or a pa articular sme
e or smell wi ill gradually
ging if the d evice is to b
future refere nce.
n page 2 of this manual
struction ns
ocation
has been de esigned for i
nit must be o operated wit
environment ts with an am
a closed env vironment sm
Overhead m mounting req
installation material to b
t attempt to install the d
result in inju uries.
led by a qua alified person
tion must be e able to sup
always be se ecured with a
elow the dev vice when it
evice once a a year and o once before y
location with h few passer
flammable m material with
be approve d by an expe
n page 2 of this manual
nect an XLR c cable to the
3-pin XLR in nput [5] of
ing cable sho ould be a du ual core, scre
ecommended d for installa
nvironment ( (e.g. discos)
se. The DMX X terminator
lugged into the XLR outp
VDPL300BA V A
All other use es may lead
n an unautho orised way w will void the
ines in this m manual is no
suing defect ts or problem ms.
warranty.
e.
r it has been exposed to
off until it ha as reached r
n stage, in d iscos, theatr
f 230 VAC/50 0 Hz.
nt operation : regular op
ell when the device is ac
disappear.
be transporte ed.
.
5 DMX input
6 sensitivity a
7 display
8 menu contr
ndoor enviro onments at t
th an unobst tructed air c
mbient temp perature hig
maller than 1 10 m³ unles
uires extens sive experien
be used... Ha ave the mate
device yours elf if you lac
n, respecting g EN 60598-
port 10 time es the weigh ht of the dev
a secondary attachment
is being mo unted, remo
you bring it i
rs-by that is inaccessible
hin a 0.5 m r radius of the
ert before th he device is t
.
female 3-pi n XLR outpu ut of a contro
the VDPL300 0BA. Multiple
eened cable
ations where e the DMX ca able has to r
). The termin nator preven nts corruptio
r is simply an n XLR plug w with a 120Ω
put socket o of the last de evice in the c
4
to short circ cuits, burns,
warranty.
ot covered b y the warran
changes in temperature
room tempe rature.
res, etc. The e VDPL300BA
eration brea aks will prolo ong their live
ctivated for t the first time
adjustment
rol push butt tons
temperature es up to 45°C
onvection to o its metal h
her than 45° °C and a rela
s forced air convection i
nce: calculat ting workload
erial and the e device itse
ck these qua lifications as
2-17 and all l other applic
ice for 1 hou
t e.g. a safet ty cable.
oved or serv iced. Have a a qualified
into service.
e to unautho orised person
e device.
taken into se ervice.
oller (not inc cl.) and the
e VDPL300B BAs can be li
with XLR inp put and outp
un a long dis
n of the digi
resistor betw
chain.
electroshoc ks,
nty and the
e. Protect th e
A should only y
es.
e. This is
C. For prope er
ousing.
ative humidi ity
s provided.
d limits,
lf checked
s improper
cable norms s.
ur without
ns.
nked throug h
put connecto ors.
stance or is in
ital control
ween pins 2
©Velleman n nv