Operating Conditions; Installation; Wiring; Commissioning - SOMFY ALTEA BL 50 WT Gebrauchsanleitung

4. Operating conditions

To ensure correct operation of the Altea BL System, check
that the carrier product component complies with the
following conditions for use:
• It must have a 63 or 70mm roller tube.
• It must have a tube with a symmetrical tab.
• In the lower locked position, your screen must be
rolled between a ¼ and 1/8 of a turn.
• At the point where the screen is in contact with
the head rail, check that the surface in contact
is rounded (10mm in diameter) to optimise the
friction of the screen on the head rail of the box.
• It must have a load bar with a minimum weight of
2.6 kg per linear metre.
• The carrier product component must be equipped
with Altea BL Locks, or equivalent, fitted onto the
runners and the load bar by the manufacturer of
the carrier product component.
• The head rail or lateral guides include high end
stops to ensure that the load bar does not enter the
head rail and that the hinges on the Altea BL Locks
are not damaged.
For information about the compatibility of the motor with
the exterior vertical blind and accessories, contact the
manufacturer of the exterior vertical blind or Somfy.

5. Installation

The carrier product component is already equipped with Altea
BL Locks and with its motor, the Altea BL 50 WT. The operations
described below are only required if the motor needs to fitted
to the other side of the carrier product component.
Motor preparation
[1] Fit the crown (a) and the drive wheel (b) to the motor.
[2] Measure the length (L) between the drive wheel (b) and
the head (c).
Tube preparation
[3] Cut the tube to the required length. Deburr and remove
the swarf.
Minimum tube : Ø 63mm
Motor/tube assembly
[4] Slide the motor into the tube, aligning
the tab and the groove on the crown.
[5] Fix the tube to the motor with four Ø 5 mm self-tapping
screws or four Ø 4.8 mm steel pop rivets, depending on
dimension (L).
Mounting the motorised tube
[6] Mount the motorised tube on the end bracket (e).
[7] Mount the tube on the motor bracket (f). Fit the stop ring (g).
12
[1]
(b)
(a)
[2] (b)
(c)
L
[3]
[4]
[5]
L
[6] [7]
(f)
(e)
(g)
Copyright © 2007 Somfy SAS. All rights reserved.

6. Wiring

Switch off the power.
b
a
N
c
Order point
d
L

7. Commissioning

[1] Switch the power back on.
Press the « d » button on the control point.
• If the vertical exterior screen rises, the wiring
is correct and commissioning is finished.
• If the vertical exterior screen is lowered,
go to the next stage.
[2] Switch off the power.
Transpose the brown wire and the black wire
connected to the control point.
[3] Switch the power back on.
Press the « d » button to check the direction
of rotation.

8. Operation

[1] ] Press the " d " button: the exterior
vertical blind is raised and stops at the top stop
without requiring adjustment.
[2] Press the " b " button: The exterior
vertical blind is lowered and stops at the
bottom stop in the Altea BL Locks without
requiring adjustment. The screen fixed in the
headrail is therefore in contact with this.
Copyright © 2007 Somfy SAS. All rights reserved.
a Blue Neutral (N)
b Brown Live, direction 1
c Black Live, direction 2
d Yellow/Green
Earth (
[1]
[2]
b
N N
[2]
c
d d
L L
[3]
[1]
[2]
)
b
c
13